模具专业英语词汇资料.doc
-Injection Mold Technical Terms(一)模具专业基本用词 Professional Terms1 塑料 plastic, resin2 样件 sample3 钢料 steel4 注塑机 injection machine, press5 产品 part, product, moulding6 模具 mold, mould, toolA 简易模(样板模) prototype mold B 量产用模具 production mold7 三维造型(数模)3D model, 3D data8 二维产品图 2D part drawing9 设计 design10 制造 manufacture, build up, construction11 检验 check, inspection12 测量 measure, inspection13 修改 change, modify, correction14 工程更改 engineer change15 质量 quality16 数量 quantity17 基准 datum, reference牛角入水-radsgate(二)如何解析2D 产品图?How to read 2D part drawing?一 产品几何 Geometry1点 point2线(边) line, edge3面 faceA 侧面 side B 表面 surface C 外观面 appearance surface4壁厚 wall thickness, stock thickness5加强筋(骨位) rib6孔 hole7细长的槽 slot8柱位 boss9角 cornerA 圆角 fillet B 倒角 chamfer C 尖角 sharp corner10斜度 angle, taper11. 凹槽recess , groove二 分模信息 Splitting1 分型线 parting line (P/L), splitting line2 主分模方向 main direction, line of draw3 浇口设定 gating产品标识 Part Identification1 产品名称 part name (P/N)2 产品编号+版本号 part number + revision (Rev.)3 型腔号 cavity number4 材料标记 material symbol5 模具编号 mold number (no.)6 日期印 dating insert, date code7 循环印 cycling code8 公司标志 company logo三 技术要求 Specification (Special Requirement)1 项目启动表 Kick-off sheet1) 项目名称 program name, project name2) 产品名称 part name, product name, part description3) 产品编号 part number (P/N)4) 客户模号 customer mold no.5) 项目启动日期 kick off date, start date6) 项目完成日期 due date, lead time7) 内模件用钢 tool steel8) 型腔数量 number of cavities 9) 数据文件编号 data file no.10) 注塑材料 resin, plastic, raw material 11) 收缩率 shrink, shrinkage, shrink factor12) 注塑机吨位 molding machine size, injection machine size13) 成型周期 cycle time14) 型腔光洁度 cavity polish15) 型芯光洁度 core polish16) 皮纹(晒纹) texture, grain17) 拔模斜度 draft angle, removal taper18) 注塑件颜色及光泽 molded color & gloss19) 模具加工地 manufacturing facility20) 热流道供应商 manifold manufacturer, manifold supplier21) 浇口位置 gate location / position22) 浇口类型 gate type23) 产品标识 stamp information, part identification 24) 特殊要求 special instructions25) 安全模数 safe steel 2 产品质量及外观要求 Part Quality & Appearance Requirement1) 尺寸及公差 Dimension & Tolerance 重要尺寸 critical dimension, important dim., key dim. 理论尺寸 nominal dimension 实际尺寸 actual dimension 公差 tolerance 公差带 tolerance range 尺寸超差 dimension deviation 接受(合格) accept, OK 拒绝(不合格) reject, refuse, obsolete, NG 让步接受 concession, special admit 返工 re-work2) 产品缺陷(常见的)Defects (normal) 缩水 sink mark, shrinkage 飞边,毛边 flash, burr 段差 mismatch discrepancy 银丝纹,蛇纹 snake marks, streak 弯曲,变形 warpage, distortion 打不饱(缺料) short shot 熔接线 weld line 多胶 unwanted plastic 拉伤damage3 产品外观 Part Appearance 产品颜色 part color 产品光泽 gloss 皮纹粒度 grain4 常用词汇、词组及短语 Normal Word, Short Sentence1) 单边 per side2) 双边 both sides3) 加入,添加 add, incorporate4) 去除,取消 remove, cancel5) 满足的要求,符合,与要求一致 according to, conform to, satisfy, meet6) 要求,需要 require, need, demand7) 确认 be approved, agreed by 8) 允许 permit, allow9) 在范围之内 within10) 不可以,不允许,禁止 free from, prevent, avoid11) ,除非有另指 unless otherwise specified12) 或少于 or less13) 自动化运作 automatic operation14) 未注尺寸(详细形状)见三维造型 Non dimensioned contour (detailed shape) see 3D model.15) 分型线上的飞边(披缝)或段差应小于 Burrs or discrepancy on the P/L shall be or less.四 标题栏 Title Block1 产品名称 part name2 图纸编号 + 版本号(索引号) drawing no. + level (index)3 一般公差 general tolerance(三) 如何阅读制模标准?How to read tooling standard?一模具结构术语 Mold Construction TermsA模架 Mold Base1 模架量化特征 Measurement Feature 长 X 宽 X 高 Length X Width X Height 模具高度尺寸(模厚) stack height of mould 模具重量 total weight of mould, mould thickness2 定模底板 front plate, top clamping plate, clamp plate, clamping plate3 定模板 cavity plate, fixed mould plate, A plate4 动模板 core plate, moving mould plate, B plate 5 浮动板 floating plate6 支撑板 support plate, backing plate7 间隔板,方铁 support blocks, rails, risers, spacer block8 顶杆固定板 retaining plate, ejector retaining plate9 顶板 ejector plate,bottom clamping plate10 动模底板 back plate11 导柱 guide pillar, leader pin, guide pin12 导套 guide bush, leader pin bush13 复位杆 return pin, push-back pin14 弹簧 spring15 撑头 support pillar16 顶针板导柱、导套 ejection guide pin / bush17 垃圾钉 stop pin, stop button18 模脚 standing-off pillars19 标牌 plaque scutcheonB成型零部件 moulding components20 型芯 core insert21 型腔 cavity insert22 镶针 core pin23 镶块 sub-insert, split24 滑块 slide, sliding split25 斜顶 lifter, angled-lift splitA 斜顶头 lifter head B 斜顶杆 lifter rod, lifter shaftC 斜顶连接块 lifter coupling D 斜顶导向块lifter guideE 斜顶导滑块lifter Gib26 成型顶杆 moulding face pin, form pinC浇注系统 Feed System1塑料 Plastica 主流道 sprueb 分流道 runner 主分流道 main runner 二级分流道 branch runner分流道断面形状 cross-sectional shape of runner 圆形 full round 半圆形 semicircular 梯形 trapezoidalc 浇口 gate常用浇口形式 normal gate type : 边缘浇口(J型浇口) edge gate, J gate 侧浇口 side gate 潜伏式浇口 sub-gate, cashew gate, subsurface gate, submarine gate 潜顶针 subgate to pin 潜伏式二次浇口(隧道式浇口) tunnel gate onto feeder post 点浇口 pin gate 直接浇口(主流道型浇口) sprue gate, direct gate 护耳式浇口 tab gated 模腔 impressione 冷料井 cold slug wellf 热流道 hot runner2模具零件 mold componentsa 定位圈 locating ring, location ring, register ring b 浇口套 sprue bushc 挡圈 stop ringd 浇口镶块 gate inserte 热流道板 manifoldf 热嘴 hot dropD分型面及其锁紧、排气 Parting Surface, inter-locking & venting1 分型线 parting line ( P/L )2 镶拼线 bodyline, joint line3 平 / 不平的分型面 flat / non flat parting surface4 封胶面 shut off surfaces, seal-off surfaces5 擦穿位 shut off6 碰穿位 kiss-off7 管位 parting line lock8 分型面的释放(避空) relief of parting surface9 分型面的平衡 balancing of parting surface10 锁紧角度 locking angle11 锁紧力 clamping force12 锁模块 safety strap13 精定位 Interlock, die lock14 困气 air trap15 排气槽 vent, vent slot16 撬模坑 - pry slot17 计数器- shot counter/ cycle counterE滑块机构 Slide1 驱动 Actuation 斜导柱 angle pin, horn pin, cam pin 弹簧 spring 油缸 hydraulic cylinder 2 制动 Detention 滑块固定器 slide retainer 弹簧制动器 spring-loaded detention (plunger) 挡钉、挡板 stop pin, stop plate, slide stop3 导轨 gib, guide strip,center guide4 锁紧块(楔紧块) heel block, locking heel, wedge block, chase block,slide driver5 耐磨片 wear plate, wear strip6 压板 retainer,gib7 螺钉 screw8 定位销 dowel pin9 行位扣 slide lock / slide retainer10 flat ejector pin 扁顶针F斜顶机构 Lifter1 斜顶头 lifter head2 斜顶杆 lifter rod, lifter shaft3 斜顶固定块lifter rod retainer4 斜顶导向块lifter guide5 开口销 split pin6 固定板(压板) retainer plate7 耐磨片 wear plate8 铜导套 bronze bushing9 导套固定板bushing retainer10 衬套 spacer11 导轨 L gib 12 导轨-T-Gib13 滑动块 slide14 连接块U-CouplingG顶出系统 Ejection System1 基本词汇 Basic Word 顶出行程 ejection stroke 模具开档 daylight 粘模 stick on 产品脱模 part is push off from, clear part of mould, separation of part2 顶板机构 Ejector plate assembly 顶板 ejector plate 顶板固定板 retaining plate 推板 stripper plate 推板导柱 ejector guide pin 推板导套 ejector guide bush 撑头 support pillar 限位块 stop block,stroke block3 复位机构 Return System 复位杆(回程杆) return pin, push back pin 垃圾钉 stop pin, stop button 压簧 compressed spring 碟簧 a stack of “Belleville” washers 早复位机构 early return system 强制复位机构 positive return system4 顶出方法 Ejection Techniques1) 顶杆顶出 pin ejection2) 顶管顶出 sleeve ejection3) 顶块顶出 bar ejection4) 扁顶顶出 blade ejection5) 顶板顶出 stripper ejection6) 油缸顶出 hydraulic ejection7) 气顶 air ejection8) 阀门顶出 valve ejection5 顶出元件 Ejection Elements1) 拉料杆 sprue puller, sucker pin2) 顶杆 ejector pin3) 阶梯式顶杆 stepped ejector pin4) 顶管 ejection sleeve, sleeve5) 扁顶 ejector blade, slabbed off ejector pin6) 顶块 stripper bar7) 顶环 stripper ring8) 推板 stripper plate9) 加速顶 accelerated ejection10) 直顶-straight lifter/EJECTOR BAR6 顶出辅助机构 Supplementary operating system1) 弹簧柱塞器 spring loaded plunger2) 弹珠定位器 ball catch system3) 插销式锁扣 Latch lock 4) 尼龙拉杆装置 friction puller device7 电器元件 Electric Components1) 压力传感器 pressure transducer2) 限位开关 limit switchF冷却系统 Cooling System1 基本词汇 Basic Word1) 温差 temperature variation2) 水孔(水道) waterlines, water-ways, flow-way, channel3) 水路 cooling circuit4) 水路示意图 water schematic, schematic circuit5) 冷却液 coolant, coolant fluid6) 内连接 interconnect7) 外连接 external connection8) 出口、入口 outlet、inlet9) 漏水 water leakage2 水路分布 Circuits1) 阶梯式水路 stepped system2) 分隔板水路 baffled hole system3) 斜孔式水路 angled hole system3 水路元件 Components1) 闷头(螺塞、止水栓) (threadless)brass pressure plug : female plug & male 2) 隔水片 baffle3) 密封圈 O ring 4) 快插水路接头 quick disconnect fitting, quick connection adaptor5) 弯头 elbow6) 偶合器(连接器、接头) adaptor (including a plug & a socket)7) 橡皮管 rubber hose8) 分水板,集水块 water manifoldG螺纹、螺纹孔 & 螺钉 Thread, thread hole & screw1 螺纹 thread2 管螺纹 pipe thread3 螺纹孔 screw hole, tapped hole4 起吊孔 handling hole, jack screw hole, eye bolt hole5 螺钉 screw6 内六角螺钉 socket headed cap screw (s.h.c.s.)7 沉头螺钉 flat headed cap screw (f.h.c.s)8 螺栓 bolt9 螺母 nut10 锁紧螺母 locknut11 螺纹标准 Thread Standard 公制标准 Metric 英制标准 Imperial 英制管螺纹标准 British Standard Pipe thread (BSP) 美制管螺纹标准 NPT 美制粗螺纹标准 United Coarse thread (UNC) 美制细螺纹标准 United Fine thread (UNF)H润滑 Lubrication1 润滑槽 grease groove2 加油管 grease line3 油杯 lubrication fittingI 测量仪器 Measuring Instruments1 游标卡尺 vernier caliper2 千分尺 micrometer3 高度规 height gauge4 刻度规 dial gauge5 三坐标测量仪(三次元) Coordinate Measure Machine(CMM)6 塞规 pin gauge7 圆角量规 radii gauge8 轮廓投影机profile projectorJ注塑机参数 Injection Machine Parameter1 注塑机规格参数 Injection Machine Specification 锁紧类型 clamp type a油缸 hydraulic b肘杆式 toggle 垂直注塑机导柱间距 tie bar vertical clearance 水平注塑机导柱间距 tie bar horizontal clearance 台板尺寸 platen dim. 最小 / 最大模厚 mold height Min. / Max., Min. / Max. mold thickness 最小 / 最大注塑机开档 open daylight Min. / Max. 锁紧行程 clamp stroke 锁紧力 clamping force 顶出行程 ejector stroke 顶出力 ejector force2 试模工艺参数 Moulding Process Parameter, machine setting 时间 Timer(TM), seca 注塑(充填)时间 filling time, injection timeb 冷却时间 cooling timec 补缩时间 packing timed 保压时间 holding timee 成型周期 cycle time 速率、速度 Velocity, %、speed, in/seca 注塑(充填)速度 injection speedb 保压速率 hold pressure velocityc 螺杆转速 screw rotation speed 压力 Pressure(Prs.), psia 注塑压力 injection pressureb 保压压力 hold pressurec 回压(背压) back pressure 温度 Temperature(Temp.), Fa 注塑机喷嘴温度 nozzle temp.b 料筒前段、中段、后段温度 barrel front、middle、rear temp.c 模温 mould temp.d 料温 purged resin melt temp.e 空射料温 air shot melt temp.
收藏
- 资源描述:
-
-`
Injection Mold Technical Terms
(一)模具专业基本用词 Professional Terms
1. 塑料 — plastic, resin
2. 样件 — sample
3. 钢料 — steel
4. 注塑机 — injection machine, press
5. 产品 — part, product, moulding
6. 模具 — mold, mould, tool
A 简易模(样板模)— prototype mold B 量产用模具 — production mold
7. 三维造型(数模)—3D model, 3D data
8. 二维产品图 — 2D part drawing
9. 设计 — design
10. 制造 — manufacture, build up, construction
11. 检验 — check, inspection
12. 测量 — measure, inspection
13. 修改 — change, modify, correction
14. 工程更改 — engineer change
15. 质量 — quality
16. 数量 — quantity
17. 基准 — datum, reference
牛角入水-radsgate
(二)如何解析2D 产品图?How to read 2D part drawing?
一. 产品几何 Geometry
1.点 — point
2.线(边) — line, edge
3.面 face
A 侧面 — side B 表面 — surface C 外观面 — appearance surface
4.壁厚 — wall thickness, stock thickness
5.加强筋(骨位) — rib
6.孔 — hole
7.细长的槽 — slot
8.柱位 — boss
9.角 — corner
A 圆角 — fillet B 倒角 — chamfer C 尖角 — sharp corner
10.斜度 — angle, taper
11. 凹槽—recess , groove
二. 分模信息 Splitting
1. 分型线 — parting line (P/L), splitting line
2. 主分模方向 — main direction, line of draw
3. 浇口设定 — gating
产品标识 Part Identification
1. 产品名称 — part name (P/N)
2. 产品编号+版本号 — part number + revision (Rev.)
3. 型腔号 — cavity number
4. 材料标记 — material symbol
5. 模具编号 — mold number (no.)
6. 日期印 — dating insert, date code
7. 循环印 — cycling code
8. 公司标志 — company logo
三. 技术要求 Specification (Special Requirement)
1. 项目启动表 Kick-off sheet
1) 项目名称 — program name, project name
2) 产品名称 — part name, product name, part description
3) 产品编号 — part number (P/N)
4) 客户模号 — customer mold no.
5) 项目启动日期 — kick off date, start date
6) 项目完成日期 — due date, lead time
7) 内模件用钢 — tool steel
8) 型腔数量 — number of cavities
9) 数据文件编号 — data file no.
10) 注塑材料 — resin, plastic, raw material
11) 收缩率 — shrink, shrinkage, shrink factor
12) 注塑机吨位 — molding machine size, injection machine size
13) 成型周期 — cycle time
14) 型腔光洁度 — cavity polish
15) 型芯光洁度 — core polish
16) 皮纹(晒纹)— texture, grain
17) 拔模斜度 — draft angle, removal taper
18) 注塑件颜色及光泽 — molded color & gloss
19) 模具加工地 — manufacturing facility
20) 热流道供应商 — manifold manufacturer, manifold supplier
21) 浇口位置 — gate location / position
22) 浇口类型 — gate type
23) 产品标识 — stamp information, part identification
24) 特殊要求 — special instructions
25) 安全模数— safe steel
2. 产品质量及外观要求 Part Quality & Appearance Requirement
1) 尺寸及公差 Dimension & Tolerance
① 重要尺寸 — critical dimension, important dim., key dim.
② 理论尺寸 — nominal dimension
③ 实际尺寸 — actual dimension
④ 公差 — tolerance
⑤ 公差带 — tolerance range
⑥ 尺寸超差 — dimension deviation
⑦ 接受(合格) — accept, OK
⑧ 拒绝(不合格) — reject, refuse, obsolete, NG
⑨ 让步接受 — concession, special admit
⑩ 返工 — re-work
2) 产品缺陷(常见的)Defects (normal)
① 缩水 — sink mark, shrinkage
② 飞边,毛边 — flash, burr
③ 段差 — mismatch discrepancy
④ 银丝纹,蛇纹 — snake marks, streak
⑤ 弯曲,变形 — warpage, distortion
⑥ 打不饱(缺料) — short shot
⑦ 熔接线 — weld line
⑧ 多胶— unwanted plastic
⑨ 拉伤—damage
3. 产品外观 Part Appearance
① 产品颜色 — part color
② 产品光泽 — gloss
③ 皮纹粒度 — grain
4. 常用词汇、词组及短语 Normal Word, Short Sentence
1) 单边 — per side
2) 双边 — both sides
3) 加入,添加 — add, incorporate
4) 去除,取消 — remove, cancel
5) 满足…的要求,符合,与…要求一致 — according to, conform to, satisfy, meet
6) 要求,需要 — require, need, demand
7) 确认 — be approved, agreed by …
8) 允许 — permit, allow
9) 在…范围之内 — within
10) 不可以,不允许,禁止 — free from, prevent, avoid
11) …,除非有另指 — … unless otherwise specified
12) …或少于 — …or less
13) 自动化运作 — automatic operation
14) 未注尺寸(详细形状)见三维造型
Non dimensioned contour (detailed shape) see 3D model.
15) 分型线上的飞边(披缝)或段差应小于…
Burrs or discrepancy on the P/L shall be … or less.
四. 标题栏 Title Block
1. 产品名称 — part name
2. 图纸编号 + 版本号(索引号)— drawing no. + level (index)
3. 一般公差 — general tolerance
(三) 如何阅读制模标准?How to read tooling standard?
一.模具结构术语 Mold Construction Terms
A.模架 Mold Base
1. 模架量化特征 Measurement Feature
① 长 X 宽 X 高 — Length X Width X Height
② 模具高度尺寸(模厚) — stack height of mould
③ 模具重量 — total weight of mould, mould thickness
2. 定模底板 — front plate, top clamping plate, clamp plate, clamping plate
3. 定模板 — cavity plate, fixed mould plate, A – plate
4. 动模板 — core plate, moving mould plate, B – plate
5. 浮动板 — floating plate
6. 支撑板 — support plate, backing plate
7. 间隔板,方铁 — support blocks, rails, risers, spacer block
8. 顶杆固定板 — retaining plate, ejector retaining plate
9. 顶板 — ejector plate,bottom clamping plate
10. 动模底板 — back plate
11. 导柱 — guide pillar, leader pin, guide pin
12. 导套 — guide bush, leader pin bush
13. 复位杆 — return pin, push-back pin
14. 弹簧 — spring
15. 撑头 — support pillar
16. 顶针板导柱、导套 — ejection guide pin / bush
17. 垃圾钉 — stop pin, stop button
18. 模脚 — standing-off pillars
19. 标牌 — plaque scutcheon
B.成型零部件 moulding components
20. 型芯 — core insert
21. 型腔 — cavity insert
22. 镶针 — core pin
23. 镶块 — sub-insert, split
24. 滑块 — slide, sliding split
25. 斜顶 — lifter, angled-lift split
A 斜顶头 — lifter head B 斜顶杆 — lifter rod, lifter shaft
C 斜顶连接块 —— lifter coupling D 斜顶导向块——lifter guide
E 斜顶导滑块——lifter Gib
26. 成型顶杆 — moulding face pin, form pin
C.浇注系统 Feed System
1.塑料 Plastic
a. 主流道 — sprue
b. 分流道 runner
① 主分流道 — main runner ② 二级分流道 — branch runner
分流道断面形状 cross-sectional shape of runner
① 圆形 — full round
② 半圆形 — semicircular
③ 梯形 — trapezoidal
c. 浇口 gate
常用浇口形式 normal gate type :
① 边缘浇口(J型浇口) — edge gate, J – gate
② 侧浇口 — side gate
③ 潜伏式浇口 — sub-gate, cashew gate, subsurface gate, submarine gate
潜顶针— subgate to pin
④ 潜伏式二次浇口(隧道式浇口) — tunnel gate onto feeder post
⑤ 点浇口 — pin gate
⑥ 直接浇口(主流道型浇口) — sprue gate, direct gate
⑦ 护耳式浇口 — tab gate
d. 模腔 — impression
e. 冷料井 — cold slug well
f. 热流道 — hot runner
2.模具零件 mold components
a. 定位圈 — locating ring, location ring, register ring
b. 浇口套 — sprue bush
c. 挡圈 — stop ring
d. 浇口镶块 — gate insert
e. 热流道板 — manifold
f. 热嘴 — hot drop
D.分型面及其锁紧、排气 Parting Surface, inter-locking & venting
1. 分型线 — parting line ( P/L )
2. 镶拼线 — bodyline, joint line
3. 平 / 不平的分型面 — flat / non – flat parting surface
4. 封胶面 — shut off surfaces, seal-off surfaces
5. 擦穿位 — shut off
6. 碰穿位 — kiss-off
7. 管位 — parting line lock
8. 分型面的释放(避空) — relief of parting surface
9. 分型面的平衡 — balancing of parting surface
10. 锁紧角度 — locking angle
11. 锁紧力 — clamping force
12. 锁模块 — safety strap
13. 精定位 — Interlock, die lock
14. 困气 — air trap
15. 排气槽 — vent, vent slot
16. 撬模坑 --- pry slot
17. 计数器--- shot counter/ cycle counter
E.滑块机构 Slide
1. 驱动 Actuation
① 斜导柱 — angle pin, horn pin, cam pin
② 弹簧 — spring
③ 油缸 — hydraulic cylinder
2. 制动 Detention
① 滑块固定器 — slide retainer
② 弹簧制动器 — spring-loaded detention (plunger)
③ 挡钉、挡板 — stop pin, stop plate, slide stop
3. 导轨 — gib, guide strip,center guide
4. 锁紧块(楔紧块)— heel block, locking heel, wedge block, chase block,slide driver
5. 耐磨片 — wear plate, wear strip
6. 压板 — retainer,gib
7. 螺钉 — screw
8. 定位销 — dowel pin
9. 行位扣 — slide lock / slide retainer
10. flat ejector pin 扁顶针
F.斜顶机构 Lifter
1. 斜顶头 — lifter head
2. 斜顶杆 — lifter rod, lifter shaft
3. 斜顶固定块—lifter rod retainer
4. 斜顶导向块—lifter guide
5. 开口销 — split pin
6. 固定板(压板) — retainer plate
7. 耐磨片 — wear plate
8. 铜导套 — bronze bushing
9. 导套固定板—bushing retainer
10. 衬套 — spacer
11. 导轨 — L – gib
12. 导轨---T-Gib
13. 滑动块 — slide
14. 连接块—U-Coupling
G.顶出系统 Ejection System
1. 基本词汇 Basic Word
① 顶出行程 — ejection stroke
② 模具开档 — daylight
③ 粘模 — stick on
④ 产品脱模 — part is push off from, clear part of mould, separation of part
2. 顶板机构 Ejector plate assembly
① 顶板 — ejector plate
② 顶板固定板 — retaining plate
③ 推板— stripper plate
④ 推板导柱 — ejector guide pin
⑤ 推板导套 — ejector guide bush
⑥ 撑头 — support pillar
⑦ 限位块 —stop block,stroke block
3. 复位机构 Return System
① 复位杆(回程杆)— return pin, push – back pin
② 垃圾钉 — stop pin, stop button
③ 压簧 — compressed spring
④ 碟簧 — a stack of “Belleville” washers
⑤ 早复位机构 — early return system
⑥ 强制复位机构 — positive return system
4. 顶出方法 Ejection Techniques
1) 顶杆顶出 — pin ejection
2) 顶管顶出 — sleeve ejection
3) 顶块顶出 — bar ejection
4) 扁顶顶出 — blade ejection
5) 顶板顶出 — stripper ejection
6) 油缸顶出 — hydraulic ejection
7) 气顶 — air ejection
8) 阀门顶出 — valve ejection
5. 顶出元件 Ejection Elements
1) 拉料杆 — sprue puller, sucker pin
2) 顶杆 — ejector pin
3) 阶梯式顶杆 — stepped ejector pin
4) 顶管 — ejection sleeve, sleeve
5) 扁顶 — ejector blade, slabbed off ejector pin
6) 顶块 — stripper bar
7) 顶环 — stripper ring
8) 推板 — stripper plate
9) 加速顶 — accelerated ejection
10) 直顶----straight lifter/EJECTOR BAR
6. 顶出辅助机构 Supplementary operating system
1) 弹簧柱塞器 — spring – loaded plunger
2) 弹珠定位器 — ball catch system
3) 插销式锁扣 — Latch – lock
4) 尼龙拉杆装置 — friction puller device
7. 电器元件 Electric Components
1) 压力传感器 — pressure transducer
2) 限位开关 — limit switch
F.冷却系统 Cooling System
1. 基本词汇 Basic Word
1) 温差 — temperature variation
2) 水孔(水道) — waterlines, water-ways, flow-way, channel
3) 水路 — cooling circuit
4) 水路示意图 — water schematic, schematic circuit
5) 冷却液 — coolant, coolant fluid
6) 内连接 — interconnect
7) 外连接 — external connection
8) 出口、入口 — outlet、inlet
9) 漏水 — water leakage
2. 水路分布 Circuits
1) 阶梯式水路 — stepped system
2) 分隔板水路 — baffled hole system
3) 斜孔式水路 — angled hole system
3. 水路元件 Components
1) 闷头(螺塞、止水栓) — (threadless)brass pressure plug : female plug & male
2) 隔水片 — baffle
3) 密封圈 — O – ring
4) 快插水路接头 — quick disconnect fitting, quick connection adaptor
5) 弯头 — elbow
6) 偶合器(连接器、接头) — adaptor (including a plug & a socket)
7) 橡皮管 — rubber hose
8) 分水板,集水块 — water manifold
G.螺纹、螺纹孔 & 螺钉 Thread, thread hole & screw
1. 螺纹 — thread
2. 管螺纹 — pipe thread
3. 螺纹孔 — screw hole, tapped hole
4. 起吊孔 — handling hole, jack screw hole, eye bolt hole
5. 螺钉 — screw
6. 内六角螺钉 — socket headed cap screw (s.h.c.s.)
7. 沉头螺钉 — flat headed cap screw (f.h.c.s)
8. 螺栓 — bolt
9. 螺母 — nut
10. 锁紧螺母 — locknut
11. 螺纹标准 Thread Standard
① 公制标准 — Metric
② 英制标准 — Imperial
③ 英制管螺纹标准 — British Standard Pipe thread (BSP)
④ 美制管螺纹标准 — NPT
⑤ 美制粗螺纹标准 — United Coarse thread (UNC)
⑥ 美制细螺纹标准 — United Fine thread (UNF)
H.润滑 Lubrication
1. 润滑槽 — grease groove
2. 加油管 — grease line
3. 油杯 — lubrication fitting
I. 测量仪器 Measuring Instruments
1. 游标卡尺 — vernier caliper
2. 千分尺 — micrometer
3. 高度规 — height gauge
4. 刻度规 — dial gauge
5. 三坐标测量仪(三次元) — Coordinate Measure Machine(CMM)
6. 塞规 — pin gauge
7. 圆角量规 — radii gauge
8. 轮廓投影机—profile projector
J.注塑机参数 Injection Machine Parameter
1. 注塑机规格参数 Injection Machine Specification
① 锁紧类型 clamp type
a.油缸 — hydraulic b.肘杆式 — toggle
② 垂直注塑机导柱间距 — tie bar vertical clearance
③ 水平注塑机导柱间距 — tie bar horizontal clearance
④ 台板尺寸 — platen dim.
⑤ 最小 / 最大模厚 — mold height Min. / Max., Min. / Max. mold thickness
⑥ 最小 / 最大注塑机开档 — open daylight Min. / Max.
⑦ 锁紧行程 — clamp stroke
⑧ 锁紧力 — clamping force
⑨ 顶出行程 — ejector stroke
⑩ 顶出力 — ejector force
2. 试模工艺参数 Moulding Process Parameter, machine setting
① 时间 Timer(TM), sec
a. 注塑(充填)时间 — filling time, injection time
b. 冷却时间 — cooling time
c. 补缩时间 — packing time
d. 保压时间 — holding time
e. 成型周期 — cycle time
② 速率、速度 Velocity, %、speed, in/sec
a. 注塑(充填)速度 — injection speed
b. 保压速率 — hold pressure velocity
c. 螺杆转速 — screw rotation speed
③ 压力 Pressure(Prs.), psi
a. 注塑压力 — injection pressure
b. 保压压力 — hold pressure
c. 回压(背压) — back pressure
④ 温度 Temperature(Temp.), F
a. 注塑机喷嘴温度 — nozzle temp.
b. 料筒前段、中段、后段温度 — barrel front、middle、rear temp.
c. 模温 — mould temp.
d. 料温 — purged resin melt temp.
e. 空射料温 — air shot melt temp.
展开阅读全文