中英对照 频谱效率.docx
《中英对照 频谱效率.docx》由会员分享,可在线阅读,更多相关《中英对照 频谱效率.docx(13页珍藏版)》请在得力文库 - 分享文档赚钱的网站上搜索。
1、编号:时间:2021年x月x日书山有路勤为径,学海无涯苦作舟页码:第13页 共13页 频谱效率 频谱效率(Spectral efficiency、Spectrum efficiency)是指在数位通信系统中的带宽限制下,可以传送的资料总量。在有限的波频谱下,物理层通信协议可以达到的使用效率有一定的限度。 链路频谱效率 数字通信系统的链路频谱效率(Link spectral efficiency)的单位是 bit/s/Hz,或(bit/s)/Hz(较少用,但更准确)。其定义为净比特率(有用信息速率,不包括纠错码)或最大吞吐量除以通信信道或数据链路的带宽(单位:赫兹)。调制效率定义为净比特率(包括
2、纠错码)除以带宽。频谱效率通常被用于分析数字调制方式的效率,有时也考虑前向纠错码(forward error correction, FEC)和其他物理层开销。在后一种情况下,1个“比特”特指一个用户比特,FEC的开销总是不包括在内的。例1:1kHz带宽中可以传送毎秒1000bit的技术,其频谱效率或调制效率均为1 bit/s/Hz。例2:电话网的V.92调制解调器在模拟电话网上以56,000 bit/s的下行速率和48,000 bit/s的上行速率传输。经由电话交换机的滤波,频率限制在300Hz到3,400Hz之间,带宽相应为 3400 300 = 3100 Hz 。频谱效率或调制效率为 5
3、6,000/3,100 = 18.1 bit/s/Hz(下行)、48,000/3,100 = 15.5 bit/s/Hz(上行)。 使用FEC 的架空调变方式可达到最大的频谱效率可以利用标本化定理来求得,信号的字母表(计算机科学)利用符号数量M来组合、各符号使用 N = log2 M bit来表示。此情况下频谱效率若不使用编码间干涉的话,无法超过2N bit/s/Hz的效率。举例来说,符号种类有8种、每个各有3bit 的话,频谱效率最高不超过6 bit/s/Hz。在使用前向错误更正编码的情形时频谱效率会降低。比如说使用1/2编码率的FEC时,编码长度会变为1.5倍,频谱效率会降低50%。频谱效
4、率降低的同时FEC可以改善信号的SN比(并非一定会有改善)。对某个SN比通信回来说、在完全没有传输错误,且编码与调变方式皆处于理想的状况时,其频谱效率的上限可哈特利定理得出。比如说SN比1即分贝为0时,无论编码与调变方式如何变化,频谱效率不会超过1 bit/s/Hz。Goodput(应用层情报使用的量)比一般在此计算的吞吐量还小,其原因为有封包再次传送、超传输协议的架空造成的。 频谱效率这个用语,会产生数值越大的话可以使周波数频谱产生更有效的误解产生。比如手机因为频谱扩散与使用FEC技术使得频谱效率低下,但SN比不好有时还是可以正常通信。因此可以使用到比周波带宽数还多的链结、以整体来看其效果可
5、以弥补频谱效率低下的缺点还有过之。如同后面会提到的,具有较为合适尺度代表”单位带宽利用率”单位的bit/s/Hz存在,这是属于分码多工(CDMA)的技术并已成为数位手机的基本构成技术。但是电话线路与有线电视网等由于没有频道相互干扰的问题,其使用的基本上皆为其SN比下最大频谱效率。 系统频谱效率 无线网络是以系统频谱效率在有限的无线周波数带宽下可以同时支援的客户数与服务进行量化。其单位为bit/s/Hz/area unit、bit/s/Hz/cell、bit/s/Hz/site 等进行计量。有可以把系统能同时支援使用者的吞吐量与goodput的总量以通信回路的带宽(Hz)来表示。这并不单影响使用
6、单一通信回路的技术,多元连接手法与无线资源管理技术也受到影响,特别是动态无线资源管理可以得到改善。定义最大goodput时,会排除掉通信回路间的相互干渉与冲突,高阶通讯协定的架空也是忽略不计的。 手机网络的容量也是以1 MHz 周波数带宽上可以同时最大连接线数来表示,即Erlang/MHz/cell、Erlangs/MHz/sector、Erlangs/MHz/km 等单位。这个数值也影响到讯息编码技术(数据压缩)、在类比电话网络也有使用。例: 以频分多址 (FDMA)与固定频道分配(FCA)为基础的手机系统在频率再利用系数是 4的时候、各基地局可以利用的是所有频谱的1/4。根据此推算、最大系
7、统频谱效率(bit/s/Hz/site)是链结频谱效率的 1/4。各基地局使用3个扇形天线将讯号分为3扇区时,被称为4/12再利用模式。各部份可以使用全频谱的1/12,因此系统的频谱效率(bit/s/Hz/cell 或 bit/s/Hz/sector)为链结频谱效率的1/12。即使链结频谱效率(bit/s/Hz)偏低,以”系统频谱效率”的観点来看,并不一定代表编码效率不好。例如、分码多工(CDMA) 频谱扩散为单一通信回路(即只有依未使用者)时,频谱效率是不好的,但是由于在同一带宽中有复数的通信回路存在,因次系统频谱效率非常好。 例: 以W-CDMA 3G 手机系统来说、打电话时最大压缩8,5
8、00 bit/s时、会造成 5 MHz 带宽的扩散,此时此连接的吞吐量为8,500/5,000,000 = 0.0017 bit/s/Hz。在这情形下同扇区内可以有同时容纳100通电话(有声音)的进行。由于各基地局以3个方向的扇形天线区分为3个扇区,在频谱扩散后、频率再利用系数会变的比1还小。此时的系统频谱效率为 1 100 0.0017 = 0.17 bit/s/Hz/site亦或 0.17/3 = 0.06 bit/s/Hz/cell(也可换算成 bit/s/Hz/sector)。频谱效率可以使用固定/动态频道分配、电力控制、 即被称为Link Adaptatio的无线资源管理技术来进行改
9、善。比较表如下表1:一般通信系统的频谱效率数值一般通信系统的频谱效率服务规格每秒频道的带宽R (Mbit/s)频道的带宽B (MHz)链结频谱效率 R/B (bit/s/Hz)典型的频率再利用系数 1/K系统频谱效率 一般 R/B/K 数值 (bit/s/Hz/site)第二世代手机(2G)GSM19930.0138 时隙 = 0.1040.20.521/70.172.75GGSM+ EDGE最大 0.384 通常 0.200.2最大 1.92 通常 1.001/70.332.75GIS-136HS + EDGE最大 0.384 通常 0.270.2最大 1.92 通常 1.351/70.45
10、第三世代手机(3G)W-CDMAFDD 1997传到手机时最大 0.3845传到手机时最大 0.0771/70.513.5GHSDPA2007传到手机时最大 14.45传到手机时最大 2.881/70.713.5GHSOPAOFDMA传到手机时最大 10010传到手机时最大 51/70.71第三世代携帯电话(3G)CDMA20001x传到手机时最大 0.1441.25传到手机时最大 0.1151/70.51Wi-FiIEEE 802.11a/g2003最大 5420最大 2.71/30.9Wi-FiIEEE 802.11n Draft 2.0 2007最大 144.420最大 7.221/32
11、.4WiMAXIEEE 802.1620049620 (1.75, 3.5, 7.)4.81/41.2数位广播DAB0.576 1.1521.7120.34 0.671/50.08 0.17数位广播DAB+ SFN0.576 1.1521.7120.34 0.67数位电视DVB-T最大 31.67 通常 22.08最大 4.0 通常 2.81/50.55数位电视DVB-T+ SFN最大 31.67 通常 22.08最大 4.0 通常 2.8数位电视DVB-H5.5 1180.68 1.41/50.14 0.28数位电视DVB-H+ SFN5.5 1180.68 1.4光纤用数位电视TV256-
12、QAM3866.3316.33 Spectral efficiency Spectral efficiency, spectrum efficiency or bandwidth efficiency refers to the information rate that can be transmitted over a given bandwidth in a specific communication system. It is a measure of how efficiently a limited frequency spectrum is utilized by the ph
13、ysical layer protocol, and sometimes by the media access control (the channel access protocol).Link spectral efficiencyThe link spectral efficiency of a digital communication system is measured in bit/s/Hz,1 or, less frequently but unambiguously, in (bit/s)/Hz. It is the net bitrate (useful informat
14、ion rate excluding error-correcting codes) or maximum throughput divided by the bandwidth in hertz of a communication channel or a data link. Alternatively, the spectral efficiency may be measured in in bit/symbol, which is equivalent to bits per channel use (bpcu), implying that the net bit rate is
15、 divided by the symbol rate (modulation rate) or line code pulse rate.Link spectral efficiency is typically used to analyse the efficiency of a digital modulation method or line code, sometimes in combination with a forward error correction (FEC) code and other physical layer overhead. In the latter
16、 case, a bit refers to a user data bit; FEC overhead is always excluded.The modulation efficiency in bit/s is the gross bitrate (including any error-correcting code) divided by the bandwidth.Example 1: A transmission technique using one kilohertz of bandwidth to transmit 1,000 bits per second has a
17、modulation efficiency of 1 (bit/s)/Hz.Example 2: A V.92 modem for the telephone network can transfer 56,000 bit/s downstream and 48,000 bit/s upstream over an analog telephone network. Due to filtering in the telephone exchange, the frequency range is limited to between 300 hertz and 3,400 hertz, co
18、rresponding to a bandwidth of 3,400 300 = 3,100 hertz. The spectral efficiency or modulation efficiency is 56,000/3,100 = 18.1 (bit/s)/Hz downstream, and 48,000/3,100 = 15.5 (bit/s)/Hz upstream.An upper bound for the attainable modulation efficiency is given by the Nyquist rate or Hartleys law as fo
19、llows: For a signaling alphabet with M alternative symbols, each symbol represents N = log2 M bits. N is the modulation efficiency measured in bit/symbol or bpcu. In the case of baseband transmission (line coding or pulse-amplitude modulation) with a baseband bandwidth (or upper cut-off frequency) B
20、, the symbol rate can not exceed 2B symbols/s in view to avoid intersymbol interference. Thus, the spectral efficiency can not exceed 2N (bit/s)/Hz in the baseband transmission case. In the passband transmission case, a signal with passband bandwidth W can be converted to an equivalent baseband sign
21、al (using undersampling or a superheterodyne receiver), with upper cut-off frequency W/2. If double-sideband modulation schemes such as QAM, ASK, PSK or OFDM are used, this results in a maximum symbol rate of W symbols/s, and in that the modulation efficiency can not exceed N (bit/s)/Hz. If digital
22、single-sideband modulation is used, the passband signal with bandwidth W corresponds to a baseband message signal with baseband bandwidth W, resulting in a maximum symbol rate of 2W and an attainable modulation efficiency of 2N (bit/s)/Hz.Example 3:An 16QAM modem has an alphabet size of M = 16 alter
23、native symbols, with N = 4 bit/symbol or bpcu. Since QAM is a form of double sideband passband transmission, the spectral efficiency cannot exceed N = 4 (bit/s)/Hz.Example 4:The 8VSB (8-level vestigial sideband) modulation scheme used in the ATSC digital television standard gives N=3 bit/symbol or b
24、pcu. Since it can be described as nearly single-side band, the modulation efficiency is close to 2N = 6 (bit/s)/Hz. In practice, ATSC transfers a gross bit rate of 32 Mbit/s over a 6 MHz wide channel, resulting in a modulation efficiency of 32/6 = 5.3 (bit/s)/Hz.Example 5:The downlink of a V.92 mode
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 中英对照 频谱效率 频谱 效率
限制150内