普通胶合板测试报告..docx
《普通胶合板测试报告..docx》由会员分享,可在线阅读,更多相关《普通胶合板测试报告..docx(9页珍藏版)》请在得力文库 - 分享文档赚钱的网站上搜索。
1、检测报Test Report检测工程:普通胶合板Test ItemsPlywood for General Use委托单位:狮山冠锋木业制品Applicant Shishca Guanfeng Wood Products Co, Ltd.检测类别:委托检验Test TypeEntrusted Test收样日期:2018-10-22Received Date October 22nd,2018考前须知Precautions1 .检测报告无本单位检测专用章或骑缝章无效。Test report is invalid if not affixed with Authorized Stamp of Te
2、st or Paging Seal.2 .检测报告无审核人、批准人签字无效。Test report is invalid without signature of verifier and approver.3 .检测报告涂改增删无效。Test report is invalid only if being supplemented, deleted or altered.4 .未经本单位书面许可不得局部复制检测报告(全部复制除外)。Without prior written permission of HJK, the test report cannot be reproduced, ex
3、cept in full.5 .除非另有说明,本报告检测结果仅对测试样品负责。Unless otherwise stated, the results shown in this test report are responsible for the delivered sample(s).6 .对检测报告假设有异议,应于收到报告之日起十五天内向检测单位提出。Objections to the test report must be submitted to HJK within 15 days of report received date.7 .样品信息由送样人提供,实验室不负责核实信息真
4、实性。The test applicant is responsible for authenticity of sample information which not subject to verification of HJK LAB.8 .上海宏骏科技实验室具备由美国IAS认可的满足ISO/IEC 17025要求的资质。Shanghai Hongjun Science & Technology Co., Ltd. is an ISO/IEC 17025-conforming test laboratory, which is accredited by International Ac
5、creditation Service, Inc.1 .样品描述/Sample Description收到的样品为普通胶合板,样品包装完整、状态完好。样品规格尺寸如下表所示。The samples received are Plywood for general use. All test samples are packed well and kept in good conditions. The dimension specifications of the samples are shown in below table.测试工程尺寸规格 长*宽*厚(mm)数量(片)含水率Moistu
6、re Content100*25*8.53胶合强度Bonding strength100*25*8.512浸渍剥禺Impregnation Delamination75*75*8.56抗弯强度Bending Strength220*50*8.512弹性模量Bending Modulus of Elasticity220*50*8.512甲醛释放量Formaldehyde Emission250*150*8.53.检测标准/Testing Standards根据客户要求,样品根据如下标准进行测试:According to applicanfs requirements, the samples
7、are tested according to the following standard: GB/T 9846-2015普通胶合板GB/T 17657-2013人造板及饰面人造板理化性能试验 ASTM D6007-2014 Standard Test Method for Determining Formaldehyde Concentrations in Air from Wood Products Using a Small-Scale Chamber.检测描述/Testing Description测试环境温度为232、相对湿度为605%。测试日期从2018年10月25日至11月6日
8、 The temperature and relative humidity of test environment are 232 and 60 + 5%, respectively. The tests were conducted from October 25th, 2018 through November 6th, 2018.2 .检测结果/Test Results序号No.测试工程Test Items单位Units标准要求Standard Requirements测试结果Test Results判定结果Conclusion1含水率Moisture Content%51411.7通
9、过 Pass2胶合强度Bonding strengthMPan类 20.701.83通过 Pass3浸渍剥离Impregnation Delaminationmm每个试件同一 胶层每边剥离 长度累计不超 过 25mm。The cumulative peeling length of each specimen does not exceed that of 25mm in the same adhesive layer.15.0N/A4抗弯强度Bending StrengthMPa21224.2通过 Pass弹性模量 Bending Modulus of ElasticityMPa200026
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 普通 胶合板 测试报告
限制150内