欧陆温控表说明书 用户手册 P104P108P116 p series 工控自动化真品就在明扬工控商城工控网文档资料.pdf
《欧陆温控表说明书 用户手册 P104P108P116 p series 工控自动化真品就在明扬工控商城工控网文档资料.pdf》由会员分享,可在线阅读,更多相关《欧陆温控表说明书 用户手册 P104P108P116 p series 工控自动化真品就在明扬工控商城工控网文档资料.pdf(126页珍藏版)》请在得力文库 - 分享文档赚钱的网站上搜索。
1、 P116,P108,P104 User Manual Piccolo Range Process Controller HA031260/7 April 2015 Piccolo Range User Manual Piccolo Range PID Temperature Controllers User Manual Part Number HA031260 Issue 7.0 April-15 Includes P116,P108 and P104 Controllers.Contents 1.Installation and Basic Operation.5 1.1 What In
2、strument Do I Have?.5 1.2 Unpacking Your Controller.5 1.3 Dimensions.5 1.4 Step 1:Installation.6 1.4.1 Panel Mounting the Controller.6 1.4.2 Panel Cut Out Sizes.6 1.4.3 Recommended minimum spacing of controllers.6 1.4.4 To Remove the Controller from its Sleeve.6 1.5 Order Code.7 1.5.1 Hardware.7 1.5
3、.2 Configuration Code.8 2.Step 2:Wiring.10 2.1 Terminal Layout P116 Controller.10 2.2 Terminal Layout P108 and P104 Controllers.10 Isolation Boundaries.11 2.3 Wire Sizes.11 2.4 Controller Power Supply.11 2.4.1 High Voltage Power Supply.11 2.4.2 Low Voltage Power Supply.11 2.5 Sensor Input(Measuring
4、Input).12 2.5.1 Thermocouple Input.12 2.5.2 RTD Input.12 2.5.3 Linear Input(mA or mV).12 2.5.4 Linear Input(Volts).12 2.5.5 Two-Wire Transmitter Inputs.12 2.6 Output 1.13 2.6.1 Relay Output(Form A,normally open).13 2.6.2 Logic(SSR drive)Output.13 2.7 Output 2.13 2.7.1 Relay Output(Form A,normally op
5、en).13 2.7.2 DC Output (P116 only).13 2.7.3 Triac Output.13 2.8 Output 3.14 2.8.1 Relay Output(Form A,normally open).14 2.8.2 DC Output.14 2.9 Output 4(AA Relay).14 2.10 General Note About Relays and Inductive Loads.14 2.11 Digital Inputs DI1&DI2.15 2.12 Current Transformer.15 2.13 Transmitter Power
6、 Supply.15 2.14 Digital Communications.16 2.15 Wiring Examples.17 2.15.1 Heat/Cool Controller.17 2.15.2 CT Wiring Diagram.17 3.Safety and EMC Information.18 3.1 Installation Safety Requirements.19 4.Switch On.21 4.1 New Unconfigured Controller.21 4.1.1 Quick Configuration Code.21 4.1.2 To Load the F
7、actory Default Data.21 4.1.3 Quick Code Tables.22 4.1.4 Alarm Allocation using the Quick Code.23 4.1.5 To Re-Enter Quick Code mode.23 4.1.6 Summary of Start-up Displays.23 4.1.7 Subsequent Start-ups.24 4.2 Front Panel Layout.24 4.2.1 To Set The Target Temperature(Setpoint SP).25 Part No HA031260 Iss
8、ue 7 CN32942 April-15 1 User Manual Piccolo Range 4.3 Level 1 Operator Parameters.25 4.4 Alarms.26 4.4.1 To Set Alarm Setpoints.26 4.4.2 Alarm Indication.26 4.4.3 To Acknowledge an Alarm.26 4.4.4 Alarm Latching.27 4.4.5 Blocking Alarms.27 4.4.6 Alarm Hysteresis.27 4.4.7 Sensor Break Alarm,Sbr.28 4.4
9、.8 Sensor Break Safe Output Demand.28 4.4.9 Loop Break Alarm,L.br.28 4.4.10 Current(CT)Alarms.28 4.4.11 EEPROM Write Frequency Warning,E2.Fr.29 4.4.12 Remote Setpoint Fail,rEm.F.29 4.5 Alarms Advanced.30 4.5.1 Behaviour of Alarms after a Power Cycle.30 4.5.2 Example 1.30 4.5.3 Example 2.30 4.5.4 Exa
10、mple 3.30 4.5.5 Diagnostic Alarms.31 4.5.6 Out of Range Indication.31 4.6 Other Levels of Operation.32 4.7 Level 2 Operation.32 4.7.1 To Select Level 2.32 4.7.2 Operator Level 2 Parameters.33 4.8 User Calibration.36 4.9 To Return to Level 1.36 4.10 Auto,Manual and Off Mode.37 4.10.1 To Select Auto,M
11、anual or Off Mode.37 4.11 Estimated Energy Usage.37 4.12 Timer Operation.38 4.12.1 Dwell Timer.38 4.12.1.1 Example:To Configure and Operate a Dwell Timer.39 4.12.1.2 Example:To Configure Timer Digital Outputs.39 4.12.1.3 Example:To Configure Timer Digital Inputs.39 4.12.2 Delayed Switch on Timer.40
12、4.12.2.1 Example:To Configure and Set up a Delayed Switch on Timer.40 4.12.3 Soft Start Timer.41 4.12.3.1 Example:To Configure and Set up a Soft Start Timer.41 5.Configuration Level.42 5.1 To Select Configuration Level.42 5.2 Configuration Level Parameters.43 5.2.1 Summary of P Codes.43 5.2.2 Analog
13、ue Input.44 5.2.3 Input Ranges and Limits.45 5.2.4 Control.46 5.2.5 Output 1.47 5.2.6 Output 2.48 5.2.7 Output 3.49 5.2.8 Output 4.50 5.2.9 DC Output Range.50 5.2.10 Setpoint Retransmission Range.50 5.2.11 Alarms.51 5.2.12 Current Transformer.52 5.2.13 Loop Break Alarm.52 5.2.14 Sensor Break,Loop Br
14、eak and Current(CT)Alarms.53 5.2.14.1 Sensor Break Impedance.53 5.2.15 Timer.54 5.2.16 Digital(Contact)Inputs.55 5.2.17 Digital Communications.56 5.2.17.1 Broadcast Communications.57 5.2.18 Pushbutton Functionality.58 5.2.19 Display Functionality.59 5.2.20 Passcodes.59 5.2.21 Energy Meter Source.60
15、5.2.22 Recovery Point.61 5.2.22.1 Recovery Point Save.61 5.2.22.2 Recovery Point Load.61 2 Part No HA031260 Issue 7 April-15 Piccolo Range User Manual 6.Controller Block Diagram.62 6.1 Input/Output.63 7.Control.64 7.1 Types of Control.64 7.1.1 On/Off Control.64 7.1.2 PID Control.64 7.1.3 Proportiona
16、l Band PB.65 7.1.4 Integral Term Ti.65 7.1.5 Derivative Term TD.66 7.1.6 Cooling Algorithm.66 7.1.7 Relative Secondary(Cool)Gain r2G.66 7.1.8 High and Low Cutback Cb.Hi and Cb.Lo.67 7.1.9 Manual Reset Nr.67 7.1.10 Loop Break.68 7.2 Tuning.69 7.2.1 Loop Response.69 7.2.2 Initial Settings.70 7.2.3 Aut
17、omatic Tuning.71 7.2.4 To Start Auto Tune.71 7.2.5 Auto Tune from Below SP Heat/Cool.72 7.2.6 Auto Tune From Below SP Heat Only.73 7.2.7 Auto Tune at Setpoint Heat/Cool.74 7.2.8 Manual Tuning.75 7.2.9 Manually Setting Relative Cool Gain.75 7.2.10 Manually Setting the Cutback Values.76 7.2.11 Effect
18、of Control Action,Hysteresis and Deadband.77 8.Digital Communications.78 8.1 Configuration Port.78 8.2 EIA485 Field Communications Port.78 8.3 Master/Slave(Broadcast)Communications.79 8.4 EEPROM Write Cycles.80 8.5 Broadcast Master Communications Connections.81 8.5.1 Wiring.81 8.6 DATA ENCODING.81 8
19、.7 Parameter Modbus Addresses.82 9.Calibration.86 9.1 To Check Input Calibration.86 9.1.1 Precautions.86 9.1.2 To Check mV Input Calibration.86 9.1.3 To Check Thermocouple Input Calibration.87 9.1.4 To Check RTD Input Calibration.87 9.2 Input Calibration.88 9.2.1 To Calibrate mV Input.88 9.2.2 To Ca
20、librate Thermocouple Input.89 9.2.3 To Calibrate RTD Input.90 9.2.4 To Calibrate mA Outputs.91 9.2.5 CT Calibration.92 9.2.6 To Return to Factory Calibration.93 9.3 Calibration Parameters.93 10.Configuration Using iTools.94 10.1 Loading an IDM.94 10.1.1 Using the H Communications Port.94 10.2 Connec
21、ting a PC to the Controller.94 10.2.1 Configuration Clip.Error!Bookmark not defined.10.3 Starting iTools.95 10.4 Configuration using the Wizard.96 10.4.1 Sensor Input.97 10.4.2 Setpoints.98 10.4.3 Control.98 10.4.4 Alarms.99 10.4.5 Timer.99 10.4.5.1 Dwell Timer.99 10.4.5.2 Delay Timer.100 10.4.5.3 S
22、oft Start Timer.100 Part No HA031260 Issue 7 April-15 3 User Manual Piccolo Range 10.4.6 Outputs.101 10.4.7 Digital Inputs.101 10.4.8 Current Transformer Input.102 10.4.9 Energy.102 10.4.10 Digital Communications.103 10.4.11 Pushbutton and Display Functionality.103 10.4.12 Promote.104 10.4.13 Exampl
23、e:Summary.104 10.5 The Browse List.105 10.5.1 Operating List.105 10.5.1.1 Settings.105 10.5.1.2 Variables.106 10.5.1.3 Status.106 10.5.1.4 User Calibration.106 10.5.2 Configuration List.107 10.5.2.1 Example:To Configure the Sensor Input.107 10.5.2.2 Example:To Configure Outputs for Control.108 10.5.
24、2.3 Example:To Configure Alarms.109 10.5.2.4 Example:To Store and Retrieve Current Settings in the Controller.110 10.5.2.5 To Load Stored Settings in the Controller.110 10.5.2.6 To Return to Factory Settings.110 10.5.2.7 To Return to Quick Start Configuration.110 10.5.3 Summary.111 10.6 Configuratio
25、ns only available using iTools.112 10.6.1 Example:To Promote Parameters.112 10.6.2 To Load A Special Linearisation Table.113 10.7 Cloning.114 10.7.1 Save to File.114 10.7.2 To Clone a New Controller.114 10.7.3 Clone Error.114 11.Appendix A Factory Default Settings.115 11.1 Factory Default Configurat
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 欧陆温控表说明书 用户手册 P104P108P116 series 工控自动化真品就在明扬工控商城工控网文档资料 欧陆 温控 说明书 自动化 真品 明扬工控 商城 工控网 文档 资料
链接地址:https://www.deliwenku.com/p-96108732.html
限制150内