阀门标准-MSS SP-105-1996(R2005) Instrument Valves for Code Applications(天选打工人).pdf
《阀门标准-MSS SP-105-1996(R2005) Instrument Valves for Code Applications(天选打工人).pdf》由会员分享,可在线阅读,更多相关《阀门标准-MSS SP-105-1996(R2005) Instrument Valves for Code Applications(天选打工人).pdf(10页珍藏版)》请在得力文库 - 分享文档赚钱的网站上搜索。
1、MSS SP-105-1996 Reaffirmed 2005 Instrument Valves for Code Applications Standard Practice Developed and Approved by the Manufacturers Standardization Society of the Valve and Fittings Industry,Inc.127 Park Street,NE Vienna,Virginia 22180 Phone:(703)281-6613 www.mss- Fax:(703)281-6671 e-mail: Copyrig
2、ht MSS Provided by IHS under license with MSSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MSS STANDARD PRACTICE SP-105 This MSS Standard Practice was developed under the consensus of the MSS Technical Committees 115 and the MSS Coordinating Committee.The content
3、 of this Standard Practice is the result of the efforts of competent and concerned volunteers to provide an effective,clear,and non-exclusive specification that will benefit the industry as a whole.This MSS Standard Practice is intended as a basis for common practice by the manufacturer,the user,and
4、 the general public.The existence of an MSS Standard Practice does not in itself preclude the manufacture,sale,or use of products not conforming to the Standard Practice.Mandatory conformance is established only by reference in a code,specification,sales contract,or public law,as applicable.Substant
5、ive changes in this 1995 edition are“flagged”by parallel bars as shown on the margins of this paragraph.The specific detail of the change may be determined by comparing the material flagged with that in the previous edition.Other standards documents referred to herein are identified by the date of i
6、ssue that was applicable to this standard at the date of issue of this standard.See Annex A.This standard shall remain silent on the applicability of those other standards of prior or subsequent dates of issue even though provisions of concern may not have changed.References contained herein which a
7、re bibliographic in nature are noted as“supp1ementalin the text.Any part of this standard may be quoted.Credit lines should read extracted from MSS SP-105,1996,Rea$jrmed 2005 with permission of the publisher,the Manufacturers Standardization Society,Reproduction pro-hibited under copyright conventio
8、n unless written permission is granted by the Manufacturers Standardization Society of the Valve and Fittings Industv,Inc.Originally Approved July 1990 Copyright O,1990 by Manufacturers Standardization Society of the Valve and Fittings Industry,Inc.Printed in U.S.A.1 Copyright MSS Provided by IHS un
9、der license with MSSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-标准分享网 w w w.b z f x w.c o m 免费下载MSS STANDARD P R A C T I C E SP-105 I CONTENTS I SECTION PAGE 1.SCOPE.1 2.DEFINITIONS.1 3.MATERIALS.1 4 UbSlCiN KbQUlKbMkN IS 2-_.5.QUALIFICATION.3 6.ACCEPTANCE TEST
10、ING.5 7.MARKING.5 FIGURE 1.DIRECT MOUNTED INSTRUMENT MANIFOLD GASKET GROOVE AND FLANGE DETAILS.4 ANNEX A.REFERENCED STANDARDS.6 11 Copyright MSS Provided by IHS under license with MSSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MSS S T A N D A R D P R A C T I C
11、E SP-105 INSTRUMENT VALVES FOR CODE APPLICATIONS 1.SCOPE 2.4.Control piping:Piping used to intercon-nect pneumatically or hydraulically operated control apparatus,or to signal transmission systems.1.1 This Standard Practice applies to small valves and manifolds developed for and pre-dominately used
12、in instrument,control and sampling piping systems.It covers steel and alloy valves of 1”nominal pipe size and smaller,and pressure ratings of 10,000 psi and lower at 100F.1.2 This Standard Practice applies to instru-ment valve designs including but not limited to needle valves,packless valves,ball v
13、alves,plug valves,check valves and manifold valves.Instru-ment valves are generally of proprietary design;this Standard Practice is not intended to define or limit designs,construction,performance,envelope dimensions,or valve types.1.3 The application of valve type,size,rating,materials of construct
14、ion,and suitability for the service are the responsibility of the pur-chaser and are outside the scope of this standard.2.DEFINITIONS 2.1 General.Definitions given in MSS SP-96 apply to this Standard Practice.2.2 Instrument valves:Valves designed for use in instrument,control and sampling piping sys
15、-3.I tems(e.g.see ASME B31.1,Article 122.3).2.3 Instrument piping:Piping used to inter-connect pneumatically or hydraulically operated control apparatus,or to signal transmission systems.2.5 Sampling piping:Piping used for the col-lection of samples(such as steam,water,oil,gas,and chemicals)from pro
16、cess systems.2.6 Manifold valve:Two or more instrument I I valves fabricated into a single valve body.2.7 Cold working pressure rating:The maxi-mum allowable working pressure of a valve at ambient conditions(-20”F to IOOF),abbrevi-ated CWP.2.8 Pressure boundary parts:The following items are defined
17、to be pressure boundary parts.Each item may not apply to all valve designs.a)Body b)Bonnet c.)Union Nut d)Body to Bonnet Bolting e)Body Bolting 2.9 Packless valve:A valve with a diaphrcigm or bellows stem seal instead of a packing or O-ring seal at the stem.MATERIALS 3.1 General.The pressure boundar
18、y parts of the valve shall be made of the materials speci-fied herein.3.2 Non-pressure boundary parts(such as the stem,glands,packing nut)shall be made of materials compatible with the pressure bound-ary parts materials.I Copyright MSS Provided by IHS under license with MSSNot for ResaleNo reproduct
19、ion or networking permitted without license from IHS-,-,-标准分享网 w w w.b z f x w.c o m 免费下载MSS S T A N D A R D P R A C T I C E SP-105 3.3 The following materials are acceptable for use as pressure boundary parts:l a)Materials listed in ASME/ANSI B16.34 b)Materials listed in ASME B3 1.1 c)Materials lis
20、ted in ASME B31.3 d)Materials listed in ASME Boiler and Presswe Vesse!Code,Sectim II!.4.1.6 The manufacturer shall provide pressure ratings for temperatures above 100F.This temperature is the temperature of the pressure-containing shell of the component.In general,this temperature is the same as tha
21、t of the contained fluid.Use of a pressure rating corre-sponding to a temperature other than that of the contained fluid is the responsibiiity of the user,subject io the requirements o appiimbie codes 3.4 Certified material test reports shall be obtained for pressure boundary parts materials.Certifi
22、cations shall include chemical analysis and mechanical properties.4.DESIGN REQUIREMENTS 4.1 Valves designed in accordance with this practice shall have their working pressure established by calculation,hydrostatic proof and burst tests or both as specified in Section 5.I and regulations.4.2 End conn
23、ections 4.2.1 Pipe threads.Tapered pipe threads shall be in accordance with one of the following:a)ANSI/ASME B1.20.1 Pipe Threads,General Purpose(Inch)b)ANSI B1.20.3 Pipe Threads,Dryseal(Inch)c)ANSI/CGA V-1 Compressed Gas Cylin-der Valve Outlet and Inlet Connections 4.1.1 Qualification of valves des
24、igned to para-graph 4.1 shall be conducted on each design and size of valve to establish the CWP rating.4.2.2 Pipe socket weld connections:The socket bore diameter and the depth of socket shall be in accordance with the dimensions and toler-4.1.2 The CWP rating of valves of identical design and size
25、 but made of different materials shall be proportional to the allowable stress of each material or may be determined by hydro-static qualification tests on valves made of each material,at the manufacturers option.4.1.3 The CWP rating of valves of identical design and size but with different end conn
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 阀门标准-MSS SP-105-1996R2005 Instrument Valves for Code Applications天选打工人 阀门 标准 MSS SP 105 1996 R2005
链接地址:https://www.deliwenku.com/p-96290527.html
限制150内