2022年思科交换机配置命令大全 .pdf
《2022年思科交换机配置命令大全 .pdf》由会员分享,可在线阅读,更多相关《2022年思科交换机配置命令大全 .pdf(19页珍藏版)》请在得力文库 - 分享文档赚钱的网站上搜索。
1、思科交换机配置命令大全switch 用户模式1:进入特权模式enable switch enable switch# 2:进入全局配置模式configure terminal switch enable switchconfigure terminal switch(conf)# 3:交换机命名hostname aptech2950 以 aptech2950 为例switch enable switchconfigure terminal switch(conf)#hostname aptch-2950 aptech2950(conf)# 4:配置使能口令enable password cis
2、co 以 cisco 为例switch enable switchconfigure terminal switch(conf)#hostname aptch2950 aptech2950(conf)# enable password cisco 5:配置使能密码enable secret ciscolab 以 cicsolab 为例switch enable switchconfigure terminal switch(conf)#hostname aptch2950 aptech2950(conf)# enable secret ciscolab 6:设置虚拟局域网vlan 1 inte
3、rface vlan 1 switch enable switchconfigure terminal switch(conf)#hostname aptch2950 aptech2950(conf)# interface vlan 1 aptech2950(conf-if)#ip address 192.168.1.1 255.255.255.0 配置交换机端口ip 和子网掩码aptech2950(conf-if)#no shut 是配置处于运行中aptech2950(conf-if)#exit aptech2950(conf)#ip default-gateway 192.168.254
4、设置网关地址7:进入交换机某一端口interface fastehernet 0/17 以 17 端口为例switch enable switchconfigure terminal 名师资料总结 - - -精品资料欢迎下载 - - - - - - - - - - - - - - - - - - 名师精心整理 - - - - - - - 第 1 页,共 19 页 - - - - - - - - - switch(conf)#hostname aptch2950 aptech2950(conf)# interface fastehernet 0/17 aptech2950(conf-if)# 8
5、:查看命令show switch enable switch# show version 察看系统中的所有版本信息show interface vlan 1 查看交换机有关ip 协议的配置信息show running-configure 查看交换机当前起作用的配置信息show interface fastethernet 0/1 察看交换机1 接口具体配置和统计信息show mac-address-table 查看 mac 地址表show mac-address-table aging-time 查看 mac 地址表自动老化时间9:交换机恢复出厂默认恢复命令switch enable swit
6、ch# erase startup-configure switch# reload 10:双工模式设置switch enable switchc onfigure terminal switch2950(conf)#hostname aptch-2950 aptech2950(conf)# interface fastehernet 0/17 以 17 端口为例aptech2950(conf-if)#duplex full/half/auto 有 full , half, auto 三个可选项11: cdp相关命令switch enable switch# show cdp 查看设备的cdp
7、 全局配置信息show cdp interface fastethernet 0/17 查看 17 端口的 cdp配置信息show cdp traffic 查看有关cdp 包的统计信息show cdp nerghbors 列出与设备相连的cisco 设备12: csico2950 的密码恢复拔下交换机电源线。用手按着交换机的MODE 键,插上电源线在 switch:后执行flash_ini 命令: switch: flash_ini 查看 flash 中的文件:switch: dir flash: 把“ config.text ”文件改名为“config.old ” : switch: ren
8、ame flash: config.text flash: config.old 执行 boot:switch: boot 交换机进入是否进入配置的对话,执行no :进入特权模式察看flash 里的文件:show flash : 名师资料总结 - - -精品资料欢迎下载 - - - - - - - - - - - - - - - - - - 名师精心整理 - - - - - - - 第 2 页,共 19 页 - - - - - - - - - 把 “config.old ” 文件改名为 “config.text ” :switch: rename flash: config.old flash
9、: config.text 把 “ config.text ” 拷 入 系 统 的 “ running-configure ”:copy flash: config.text system : running-configure 把配置模式重新设置密码存盘,密码恢复成功。13:交换机telnet 远程登录设置:switchen switchconfigure terminal switch(conf)#hostname aptech-2950 aptech2950(conf)#enable password cisco 以 cisco 为特权模式密码aptech2950(conf)#inter
10、face fastethernet 0/1 以 17 端口为 telnet 远程登录端口aptech2950(conf-if)#ip address 192.168.1.1 255.255.255.0 aptech2950(conf-if)#no shut aptech2950(conf-if)#exit aptech2950(conf)line vty 0 4 设置 0-4 个用户可以telnet 远程登陆aptech2950(conf-line)#login aptech2950(conf-line)#password edge 以 edge为远程登录的用户密码主机设置:ip 192.16
11、8.1.2 主机的ip 必须和交换机端口的地址在同一网络段netmask 255.255.255.0 gate-way 192.168.1.1 网关地址是交换机端口地址运行:telnet 192.168.1.1 进入 telnet 远程登录界面password : edge aptech2950en password: cisco aptech# 14:交换机配置的重新载入和保存设置完成交换机的配置后:aptech2950(conf)#reload 是否保存( y/n)y: 保存设置信息n:不保存设置信息1.在基于 IOS 的交换机上设置主机名/系统名 : switch(config)# ho
12、stname hostname 在基于 CLI 的交换机上设置主机名/系统名 : switch(enable) set system name name-string 2.在基于 IOS 的交换机上设置登录口令: switch(config)# enable password level 1 password 名师资料总结 - - -精品资料欢迎下载 - - - - - - - - - - - - - - - - - - 名师精心整理 - - - - - - - 第 3 页,共 19 页 - - - - - - - - - 在基于 CLI 的交换机上设置登录口令: switch(enable)
13、 set password switch(enable) set enalbepass 3.在基于 IOS 的交换机上设置远程访问: switch(config)# interface vlan 1 switch(config-if)# ip address ip-address netmask switch(config-if)# ip default-gateway ip-address 在基于 CLI 的交换机上设置远程访问: switch(enable) set interface sc0 ip-address netmask broadcast-address switch(enab
14、le) set interface sc0 vlan switch(enable) set ip route default gateway 4.在基于 IOS 的交换机上启用和浏览CDP 信息 : switch(config-if)# cdp enable switch(config-if)# no cdp enable 为了查看 Cisco 邻接设备的CDP 通告信息 : switch# show cdp interface type modle/port switch# show cdp neighbors type module/port detail 在基于 CLI 的交换机上启用和
15、浏览CDP 信息 : switch(enable) set cdp enable|disable module/port 为了查看 Cisco 邻接设备的CDP 通告信息 : switch(enable) show cdp neighborsmodule/port vlan|duplex|capabilities|detail 5.基于 IOS 的交换机的端口描述: switch(config-if)# description description-string 基于 CLI 的交换机的端口描述: switch(enable)set port name module/number descr
16、iption-string 6.在基于 IOS 的交换机上设置端口速度: switch(config-if)# speed10|100|auto 在基于 CLI 的交换机上设置端口速度: switch(enable) set port speed moudle/number 10|100|auto switch(enable) set port speed moudle/number 4|16|auto 7.在基于 IOS 的交换机上设置以太网的链路模式: switch(config-if)# duplex auto|full|half 在基于 CLI 的交换机上设置以太网的链路模式: swi
17、tch(enable) set port duplex module/number full|half 8.在基于 IOS 的交换机上配置静态VLAN: switch# vlan database switch(vlan)# vlan vlan-num name vla 名师资料总结 - - -精品资料欢迎下载 - - - - - - - - - - - - - - - - - - 名师精心整理 - - - - - - - 第 4 页,共 19 页 - - - - - - - - - switch(vlan)# exit switch# configure teriminal switch(c
18、onfig)# interface interface module/number switch(config-if)# switchport mode access switch(config-if)# switchport access vlan vlan-num switch(config-if)# end 在基于 CLI 的交换机上配置静态VLAN: switch(enable) set vlan vlan-num name name switch(enable) set vlan vlan-num mod-num/port-list 9. 在基于 IOS 的交换机上配置VLAN 中继
19、线 : switch(config)# interface interface mod/port switch(config-if)# switchport mode trunk switch(config-if)# switchport trunk encapsulation isl|dotlq switch(config-if)# switchport trunk allowed vlan remove vlan-list switch(config-if)# switchport trunk allowed vlan add vlan-list 在基于 CLI 的交换机上配置VLAN中继
20、线 : switch(enable) set trunk module/port on|off|desirable|auto|nonegotiate Vlan-range isl|dotlq|dotl0|lane|negotiate 10.在基于 IOS 的交换机上配置VTP 管理域 : switch# vlan database switch(vlan)# vtp domain domain-name 在基于 CLI 的交换机上配置VTP 管理域 : switch(enable) set vtp domain domain-name 11.在基于 IOS 的交换机上配置VTP 模式 : sw
21、itch# vlan database switch(vlan)# vtp domain domain-name switch(vlan)# vtp sever|cilent|transparent switch(vlan)# vtp password password 在基于 CLI 的交换机上配置VTP 模式 : switch(enable) set vtp domain domain-name mode sever|cilent|transparent password password 12. 在基于 IOS 的交换机上配置VTP 版本 : switch# vlan database
22、switch(vlan)# vtp v2-mode 在基于 CLI 的交换机上配置VTP 版本 : switch(enable) set vtp v2 enable 13. 在基于 IOS 的交换机上启动VTP 剪裁 : switch# vlan database switch(vlan)# vtp pruning 名师资料总结 - - -精品资料欢迎下载 - - - - - - - - - - - - - - - - - - 名师精心整理 - - - - - - - 第 5 页,共 19 页 - - - - - - - - - 在基于 CL I 的交换机上启动VTP 剪裁 : switch(
23、enable) set vtp pruning enable 14.在基于 IOS 的交换机上配置以太信道: switch(config-if)# port group group-number distribution source|destination 在基于 CLI 的交换机上配置以太信道: switch(enable) set port channel moudle/port-range modeon|off|desirable|auto 15.在基于 IOS 的交换机上调整根路径成本: switch(config-if)# spanning-tree vlan vlan-list
24、cost cost 在基于 CLI 的交换机上调整根路径成本: switch(enable) set spantree portcost moudle/port cost switch(enable) set spantree portvlancost moudle/port cost costvlan-list 16.在基于 IOS 的交换机上调整端口ID: switch(config-if)# spanning-treevlan vlan-listport-priority port-priority 在基于 CLI 的交换机上调整端口ID: switch(enable) set span
25、tree portpri mldule/portpriority switch(enable) set spantree portvlanpri module/portpriority vlans 17. 在基于 IOS 的交换机上修改STP 时钟 : switch(config)# spanning-tree vlan vlan-list hello-time seconds switch(config)# spanning-tree vlan vlan-list forward-time seconds switch(config)# spanning-tree vlan vlan-lis
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 2022年思科交换机配置命令大全 2022 思科 交换机 配置 命令 大全
限制150内