最新AT89s51单片机外文翻译.doc
《最新AT89s51单片机外文翻译.doc》由会员分享,可在线阅读,更多相关《最新AT89s51单片机外文翻译.doc(24页珍藏版)》请在得力文库 - 分享文档赚钱的网站上搜索。
1、Four short words sum up what has lifted most successful individuals above the crowd: a little bit more.-author-dateAT89s51单片机外文翻译外文翻译毕业设计(论文)外文翻译 毕业设计(论文)题目:基于单片机的点阵LED显示屏系统的设计 外文题目:The Description of AT89S51 译文题目:AT89S51概述学生姓名: 费禹翔 专 业:电气工程及其自动化0603班 指导教师: 李翠玉 -The Description of AT89S511 General D
2、escriptionThe AT89S51 is a low-power, high-performance CMOS 8-bit microcontroller with 4K bytes of In-System Programmable Flash memory. The device is manufactured using Atmels high-density nonvolatile memory technology and is compatible with the industry-standard 80C51 instruction set and pinout. Th
3、e on-chip Flash allows the program memory to be reprogrammed in-system or by a conventional nonvolatile memory programmer. By combining a versatile 8-bit CPU with In-System Programmable Flash on a monolithic chip, the Atmel AT89S51 is a powerful microcontroller which provides a highly-flexible and c
4、ost-effective solution to many embedded control applications.The AT89S51 provides the following standard features: 4K bytes of Flash, 128 bytes of RAM, 32 I/O lines, Watchdog timer, two data pointers, two 16-bit timer/counters, a five-vector two-level interrupt architecture, a full duplex serial por
5、t, on-chip oscillator, and clock circuitry. In addition, the AT89S51 is designed with static logic for operation down to zero frequency and supports two software selectable power saving modes. The Idle Mode stops the CPU while allowing the RAM, timer/counters, serial port, and interrupt system to co
6、ntinue functioning. The Power-down mode saves the RAM contents but freezes the oscillator, disabling all other chip functions until the next external interrupt or hardware reset.2 PortsPort 0 is an 8-bit open drain bi-directional I/O port. As an output port, each pin can sink eight TTL inputs. When
7、1s are written to port 0 pins, the pins can be used as high-impedance inputs. Port 0 can also be configured to be the multiplexed low-order address/data bus during accesses to external program and data memory. In this mode, P0 has internal pull-ups. Port 0 also receives the code bytes during Flash p
8、rogramming and outputs the code bytes during program verification. External pull-ups are required during program verification.Port 1 is an 8-bit bi-directional I/O port with internal pull-ups. The Port 1 output buffers can sink/source four TTL inputs. When 1s are written to Port 1 pins, they are pul
9、led high by the internal pull-ups and can be used as inputs. As inputs, Port 1 pins that are externally being pulled low will source current (IIL) because of the internal pull-ups. Port 1 also receives the low-order address bytes during Flash programming and verification.Port PinAlternate FunctionsP
10、1.5MOSI (used for In-System Programming)P1.6MOSO (used for In-System Programming)P1.7 SCK(used for In-System Programming)Port 2 is an 8-bit bi-directional I/O port with internal pull-ups. The Port 2 output buffers can sink/source four TTL inputs. When 1s are written to Port 2 pins, they are pulled h
11、igh by the internal pull-ups and can be used as inputs. As inputs, Port 2 pins that are externally being pulled low will source current (IIL) because of the internal pull-ups.Port 2 emits the high-order address byte during fetches from external program memory and during accesses to external data mem
12、ory that use 16-bit addresses (MOVX DPTR). In this application, Port 2 uses strong internal pull-ups when emitting 1s. During accesses to external data memory that use 8-bit addresses (MOVX RI), Port 2 emits the contents of the P2 Special Function Register. Port 2 also receives the high-order addres
13、s bits and some control signals during Flash programming and verification.Port 3 is an 8-bit bi-directional I/O port with internal pull-ups. The Port 3 output buffers can sink/source four TTL inputs. When 1s are written to Port 3 pins, they are pulled high by the internal pull-ups and can be used as
14、 inputs. As inputs, Port 3 pins that are externally being pulled low will source current (IIL) because of the pull-ups. Port 3 receives some control signals for Flash programming and verification. Port 3 also serves the functions of various special features of the AT89S51, as shown in the following
15、table.Port PinAlternate FunctionsP3.0RXD(serial input port)P3.1TXD(serial output port)P3.2INT0(external interrupt 0)P3.3INT1(external interrupt 1)P3.4T0(timer 0 external input)P3.5T1(timer 1 external input)P3.6WR(external data memory write strobe)P3.7RD(external data memory read strobe)3 Special Fun
16、ction RegistersA map of the on-chip memory area called the Special Function Register (SFR) space is shown in Table 3-1. Table 3-1. AT89S51 SFR Map and Reset Values0F8H 0FFH 0F0H B 00000000 0F7H 0E8H 0EFH 0E0H ACC 00000000 0E7H 0D8H 0DFH 0D0H PSW 00000000 0D7H 0C8H 0CFH 0C0H 0C7H 0B8H IP XX000000 0BF
17、H 0B0H P3 11111111 0B7H 0A8H IE 0X000000 0AFH 0A0H P2 11111111 AUXR1 XXXXXXX0 WDTRST XXXXXXXX 0A7H 98H SCON 00000000 SBUF XXXXXXXX 9FH 90H P1 11111111 97H 88H TCON 00000000 TMOD 00000000 TL0 00000000 TL1 00000000 TH0 00000000 TH1 00000000 AUXR XXX00XX 8FH 80H P0 11111111 SP 00000111 DP0L 00000000 DP
18、0H 00000000 DP1L 00000000 DP1H 00000000 PCON 0XXX0000 87H Note that not all of the addresses are occupied, and unoccupied addresses may not be implemented on the chip. Read accesses to these addresses will in general return random data, and write accesses will have an indeterminate effect. User soft
19、ware should not write 1s to these unlisted locations, since they may be used in future products to invoke new features. In that case, the reset or inactive values of the new bits will always be 0. Interrupt Registers: The individual interrupt enable bits are in the IE register. Two priorities can be
20、 set for each of the five interrupt sources in the IP register.Table 3-2. AUXR:Auxiliary RegisterAUXR Address=8EH Reset Value=XXX00XX0b Not Bit Addressable WDIDLE DISRTO DISALEBit 7 6 5 4 3 2 1 0 Reserved for future expansionDISALE Disable/Enable ALE DISALE Operating Mode 0 ALE is emitted at a const
21、ant rate of 1/6 the oscillator frequency 1 ALE is active only during a MOVX or MOVC instruction DISRTO Disable/Enable Reset-out DISRTO 0 Reset pin is driven High after WDT times out 1 Reset pin is input only WDIDLE Disable/Enable WDT in IDLE modeWDIDLE0 WDT continues to count in IDLE mode 1 WDT halt
22、s counting in IDLE mode Dual Data Pointer Registers: To facilitate accessing both internal and external data memory, two banks of 16-bit Data Pointer Registers are provided: DP0 at SFR address locations 82H-83H and DP1 at 84H-85H. Bit DPS = 0 in SFR AUXR1 selects DP0 and DPS = 1 selects DP1. The use
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 最新 AT89s51 单片机 外文 翻译
限制150内