MB主板上电过程.ppt
《MB主板上电过程.ppt》由会员分享,可在线阅读,更多相关《MB主板上电过程.ppt(35页珍藏版)》请在得力文库 - 分享文档赚钱的网站上搜索。
1、MB主板上電過程主板上電過程前言n電腦的開機只需要對著Power鍵輕輕一按即可.n可這一按具體是如何使電腦能開機工作的呢?它的整個過程是怎樣的?n以下分幾個部分做講解Contentn開機上電動作圖解n主板的電壓定義n主板的主要開機信號介紹n主板開機上電過程(波形和電路)PWRBTNSlp-s3(+)Pson#(-)+5v+3v+12v/-12v+5v+3vPower okNB_ RESETResetSBNBCPUPOWERSUPER I/OOR AS016Cpu rstIntel chipset power on sequencePwr okPower SequenceMB Power Seq
2、uence主板基本電壓(電源控制IC)POWERSpecification+12V11.4 12.6V-12V-10.8 13.2V+5V4.75 5.25V+3.3V3.14 3.47V+5VSB4.75 5.25V n主板基本電壓有5個,其他電壓都是由這5個基本電壓轉換而得.主板基本電壓Item Global StatesSleepingStatesDetail description1G0S0電腦的正常工作狀態電腦的正常工作狀態-作業系統和應用程式都在執行作業系統和應用程式都在執行2G1S1最耗電的睡眠模式最耗電的睡眠模式,所有原件均有保持電源,除了一些沒有被所有原件均有保持電源,除了一
3、些沒有被使用的使用的device.S3Suspend to RAM,只有,只有memory是唯一有電源供給的原是唯一有電源供給的原件件,XP系統下叫做系統下叫做“待機待機(Standby)”,Vista叫做叫做“睡眠睡眠(Sleep)”.S4Suspend to HDD,在,在Windows中叫休眠中叫休眠(Hibernation),所所有主記憶體儲器的有主記憶體儲器的內內容被儲存在硬碟中,從容被儲存在硬碟中,從S4恢復後,使用恢復後,使用者可以恢復到原本的工作狀態者可以恢復到原本的工作狀態.3G2S5Soft off,只有,只有standby power 存在存在.4G3BatteryMec
4、hanical Off,Power cord被拔掉,只有被拔掉,只有Battery.ACPI的Global States分四個狀態G0G1G2G3ACPI表示高級配置和電源管理介面對於Windows2000,ACPI定義了Windows、BIOS和系統硬體之間的新型工作介面。這些新介面包括Windows 控制電源管理和設備配置的機制。主板基本電壓狀態電壓種類有狀態電壓種類有3種種n1.Main power:S0/S1n2.Dual power:S0/S1/S3n3.Standby power:S0/S1/S3/S4/S5詳細參考附件:詳細參考附件:Main Power Main power的產
5、生由的產生由SLP_S3#去控制去控制。按Power Button PWRBTN#拉low 通知SIOSIO告知NB NB送出SLP_S3#(此時SLP_S3#為高電平)PSON#被拉low Power Supply產生Main Power.Power-up(Main Power)CH1:+12VCh2:+5VCh3:+3V1.Main power(+12V,+5V,+3V)almost ramp up at the same time.2.The main power ramp behavior depends on the power supply design.Standby Power
6、 1,在MB上,power supply只提供+5VSB一種standby電壓,其他standby power都由它轉出來的。2,Standby power上電(插上power cord)主板就會有,但其提供的電流有限。Dual Power Dual power由standby power和main power提供,他存在於S0,S1,S3這幾種狀態下,由Gate信號去控制哪一個power輸出。主板信號簡介n nRTCRST#nRSMRST#n nPWRBTN#nSLP_S3#nPS_ON#nPWROKnPLTRST#RTCRST#Battery3.0VBATT2.6VG3 State1.BA
7、TT comes from BATTERY at G3 state.So BATT will be 2.6V at G3 state.2.BATT comes from+3VSB at S5 state.So BATT will be 2.9V at S5 state.S5 State2.9VnRTCRST#有效:在G3狀態時,拔掉battery,此時SB收到低電平,會清掉COMS 內容;若要給主板維持時間或CMOS內容,RTCRST信號需要是高電平.+3VSBS5 State+5VSBRSMRST1.After plugging power cord,+5VSB ramps up.2.+3V
8、SB is regulated from+5VSB.3.32ms after+3VSB ramps above VTRIP(2.2V),RSMRST asserts.4.RSMRST will re-assert after AC power loss,which acts like a wake up event of SB and causes the de-assertion of SLP_S3#to turn on the system.RSMRST#Resume reset active表示所有的standby power都OK.RSMRST#:Resume Well Reset,t
9、his signal is used for resetting the resume power plane logic.AUXOK Logic Example:1.Let VPQ3.1 ramps up slower than+3VSB.It is to meet the spec that RSMRST(AUXOK)needs to ramp up after VTR is ready with a delay(20ms for SB600).2.To precisely estimate the resulting delay from+3VSB to AUXOK,we need to
10、 implement the RC charge formula.VCIf VCC=3.3V,assuming 20ms is needed:1.t=RC=20ms VC(20ms)=2.08V2.VC(18.63ms)=2V3.If VCC=5V,assuming 20ms is needed:4.2.t=RC=20ms VC(20ms)=3.16V 5.VC(10.22ms)=2V 6.RC is chosen by substituting VC(t),VCC,t and solve for RC.RSMRST#PWRBTN#PWRBTNPWRBTN#:Power ButtonPower
11、 Button,#:#:代表低電平有效代表低電平有效PWRBTN#1.Pin6 and pin8 is connected to the power button on the chassis.2.Pressing power button generate a low pulse to SB and SIO.3.Power button can be programmed to generate suspend,hibernate or shut-down event.4.Generally PWRBTN#of SB is internal pulled high,R1336 is rese
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- MB 主板 过程
限制150内