660MW火电机组锅炉水压试验措施.pdf
《660MW火电机组锅炉水压试验措施.pdf》由会员分享,可在线阅读,更多相关《660MW火电机组锅炉水压试验措施.pdf(22页珍藏版)》请在得力文库 - 分享文档赚钱的网站上搜索。
1、 1/1 1.编制依据 1.1电力建设施工质量验收及评定规程第2 部分:锅炉机组DL/T5210.2-2009 1.2电力建设施工技术规范第2 部分:锅炉机组DL/T5190.2-2012 1.4电力建设施工质量验收及评定规程第5 部分:管道及系统DL/T 5190.5-2012 1.5电力基本建设热力设备化学监督导则DL/T 889-2004 1.6火力发电厂焊接技术规程DL/T869-2012;1.7ASME动力管道B31.1-2010 1.8电力建设安全工作规程第1 部分:火力发电厂DL5009.1-2002;1.9工程建设强制性条文(电力工程部分)2011 版;2.0锅炉说明书锅炉安装
2、(哈尔滨锅炉厂有限责任公司编制)2.1锅炉本体说明书(哈尔滨锅炉厂有限责任公司编制)2.作业范围及工程量 2.1工程概况 1660MW机组锅炉是哈尔滨锅炉厂有限公司,根据哈锅自主研发技术设计、制造的超临界锅炉。该锅炉为变压运行、一次中间再热、单炉膛、平衡通风、固态排渣、全钢架悬吊结构、露天布置的“”型超临界直流锅炉。带有内置式再循环泵的启动系统,采用低NOX燃烧技术,24 只燃烧器分 6层布置,采用切圆燃烧方式,受热面呈“”型布置,炉膛上部有屏式过热器;水平烟道中布置有末级过热器、末级再热器;后烟道有中间隔墙,竖井前部布置水平低温再热器、立式低温再热器,竖井后部布置水平低温过热器、立式低温过热
3、器和省煤器。锅炉型号 boiler model:HG2076/25.4HM16 主要参数 main parameter 过热蒸汽 superheated steam:BMCR 流量 flow 2076.41t/h BMCR 出口压力 outlet pressure 25.4MPa BMCR 出口蒸汽温度 steam temperature of outlet571C 再热蒸汽 reheated steam:BMCR 蒸汽流量 steam flow 1728.61t/h 进/出口蒸汽压力 steam pressure of inlet&outlet4.464/4.274MPa 进口/出口蒸汽温度
4、 steam temperature of inlet&outlet318.8/569 1/1 给水温度 feed-water temperature:291.4 2.2作业范围及主要工程量 锅炉水压试验范围:本次水压包括一次汽系统及连接管道、二次汽系统及连接管道、锅炉本体范围内一次门以内的承压管道。具体如下:2.2.1 一次汽系统包括:主给水及给水旁路电动闸阀(10LAB70AA003、10LAB70AA002)、过热器减温水总管 3#闸阀后至省煤器入口集箱间管道、省煤器、省煤器连接导管(溢流管路暖管至 10HAC13AA005 电动截止阀)、循环泵暖管、四侧水冷壁、汽水分离器、贮水箱、启动
5、循环泵壳(含临时堵板)、顶棚过热器、包墙过热器、中间隔墙、低温过热器、一级减温器(至过热器一级喷水减温 10LAE11AA002、10LAE11AA004 电动截止阀)、分隔屏过热器、二级减温器(至过热器二级喷水减温 10LAE12AA002、10LAE12AA004 电动截止阀)、末级过热器、主汽管道(J 列柱中心向炉前 2190mm 处)水压堵板前部分。锅炉本体过热器系统:末级过热器出口至安全阀水压试验堵头。2.2.2 二次汽系统包括:冷段管道水压试验堵阀后至低温再热器入口集箱间管道、低温再热器、减温器喷嘴暖管、再热器减温器(至再热器喷水减温器管路 10LAF70AA011、10LAF70
6、AA013 电动截止阀)末级再热器、末级再热器出口管道水压堵阀前部分。2.2.3 锅炉本体范围内一次门以内承压管道 2.2.3.1 疏放水管道:包墙及低过疏水 給水疏水 折焰角入口汇集集箱疏水 drainage of the furnace arch inlet collection header 水冷壁中间集箱疏水 drainage of the header at the water-cooled wall middle 低温再热器疏水 drainage of the low temperature reheater 减温水疏水 drainage of the desuperheating
7、 water 循环泵再循环管疏水 drainage of the circulating pump recirculating pipe 水冷壁疏水 drainage of the water-cooled wall 2.2.3.2 放气管道 顶棚入口管道放气 air vent of the ceiling inlet pipeline 顶棚旁路管道放气 air vent of the ceiling bypass pipeline 分离器入口连接管道放气 air vent of the separator inlet connection pipeline 1/1 下降管放气 air ven
8、t of the downcomer 水冷壁中间集箱平衡管放气 air vent of the balance pipe of the water-cooled wall middle header 包墙连接管放气 air vent of the wrapped wall connection pipe 分隔屏入口集箱连接管放气 air vent of the connection pipe of the separated platen inlet header 省煤器出口放气 air vent of the economizer outlet 充氮管道放气 air vent of the
9、nitrogen filling pipeline 2.2.3.3 蒸汽及炉水取样管道:顶棚入口管道取样 sampling of the ceiling inlet pipeline 溢流管取样 sampling of the overflow pipe 省煤器入口取样 sampling of the economizer inlet 过热器减温器取样 sampling of the superheater desuperheator 循环泵再循环管取样 sampling of the circulating pump recirculating pipe 过热器出口取样 sampling o
10、f the superheater outlet 再热器出口管道取样 sampling of the reheater outlet pipeline 2.2.3.4 本体及预热器吹灰器汽源引出管及一次门 2.2.3.5 锅炉本体水压试验临时系统。2.3 锅炉本体水压时各系统水容积 名称 name 省煤器 economizer 启动系统Start-up system 水冷壁 Water-cooled wall 过热器 superheater 再热器 reheater 临时系统 Temporary system 合计 total 容积(M3)capacity 6 50 765 2.4 水压试验用
11、药量 锅炉水压上水加药量按照联氨含量为 250300mg/L、PH值为 1010.5。加药量计算:水压用水容积为 2000 m(包括附属管道和临时管道及冲洗用水,按照2.6 倍水容积准备除盐水)故 50%浓度联氨(N2H4)用量为:2000100030010-6 50%=1200kg 1/1 考虑裕量:50%浓度联氨用量按 1400kg备药 25%浓度的氨水(NH3H2O)含量按 500 mg/L计算 25%浓度的氨水用量为:2000100050010-625%=4000kg 考虑裕量:25%浓度的氨水用量按 4200kg备药。2.5锅炉整体水压试验压力 直流炉水压试验按 ASME 规范分两部
12、分进行,锅炉的汽水系统、过热器和省煤器作为一次汽系统,以 1.5 倍锅炉末级过热器出口设计压力(最高允许工作压力)进行水压试验;再热器系统以1.5倍一级再热器入口集箱设计压力(最高允许工作压力)进行水压试验。即:一次汽水压试验压力为27.51.5=41.25MPa 二次汽水压试验压力为 5.21.5=7.8MPa 2.6 水压试验的目的:2.6.1 检验锅炉受压部件的强度。2.6.2 检验锅炉受压部件的严密性。3.施工前具备的条件 3.1水压试验方案编制完成,经审批合格。3.2 水压范围内的所有受压件焊接工作全部结束,并已无损检测和热处理完毕,返修口已全部处理完并检验合格。所有合金元件的材质均
13、经过核对,并确认无错用现象。3.3 锅炉密封装置一次密封件安装、焊接完毕(主要包括顶棚及分隔屏内护板、后烟道顶棚管内护板、后烟道烟气分配折流板、水平烟道后部内护板、后烟道膨胀节、尾部烟道膨胀密封装置等)。3.4 锅炉附件安装完毕(主要包括吹灰孔、看火孔、检修孔、热工测点密封盒、火焰电视监视孔、绳孔装置等)。3.5所有吊杆受力均匀,临时加固支撑件全部拆除,悬吊部件全部处于自由状态。3.6临时上水管施工结束,排水通畅,楼梯通道畅通安全,炉膛内外照明良好。3.7水压试验临时管路冲洗完成,目测水质澄清,上水泵、启动升压泵经试转合格。3.8所有膨胀指示器安装完毕并调整到零位。3.9 3000m除盐水箱除
14、盐水满足水压用水量和水质要求。锅炉整体水压试验要求环境温度不得低于 5;3.10 水压试验用压力表、温度表等仪表经校验合格,安装位置合理,并配备有备用表,防止升压过程中因为管道震动而造成压力表损坏。1/1 3.11 水压试验用的临时堵板必须经过强度校核,水压试验期间非工作人员不得进入现场,停止锅炉范围内的一切施工。3.12 在水压试验前对受压部件进行风压试验,风压试验压力为 0.3MPa,试验介质为压缩空气。3.13 水压试验安全、技术、质量措施已交底并办理相关手续,水压试验组织机构和人员分工已落实。参与水压试验的系统、阀门、水泵及电气操作设备均应标识清楚,并挂临时标识牌。操作卡已编制好,操作
15、人员已掌握。3.14水压试验系统图、升降压曲线图、组织机构图已张挂于现场。3.15锅炉注水前与业主一同对锅炉钢结构的沉降观测点进行检查。4.工期要求及劳动力配备 4.1工期要求 计划开工日期 2015年 11月 20日,计划完成日期 2015年 11月 30日。4.2劳动力配置计划 序号 No.作业人员/工种 Types of worker 数量 quantity 职责 duty 1 总指挥 General director 1 负责锅炉水压的整体控制工作。In charge of boiler hydraulic pressure.2 副总指挥 Vice director-general 2
16、 协调、组织水压试验的实施工作。Coordinate and organize implementation works of hydraulic test.3 操作组负责人Operation group director 2 负责锅炉上水、停泵检查、升压、泄压等所有操作的指挥、控制工作。In charge of all the operation commands and control works related to water filling,pumping cease inspection,boost,pressure relief and so on.4 阀门操作负责人Valve
17、operation director 2 负责水压过程中阀门操作的安排及检查工作。Responsible for arranging and inspection work pressure during the valve operation.5 水泵操作负责人 The pump operation director 2 负责上水泵、升压泵的启动及停止操作工作,负责上水泵、升压泵的检查及维护工作。In charge of charging pump,booster pump launch and halt operations,and inspection and maintenance o
18、perations about charging pump and booster pump.6 水箱加药负责人 Water tank dosing director 1 负责上水前除盐水箱加药工作,负责加药数量的记录工作。In charge of demineralized water tank dosing operation,and the dose quantity record before water charging.7 升压力记录人 Pressure recorder 1 负责水压期间一、二次系统升压及泄压记录工作。In charge of records about prim
19、ary,secondary system boost and pressure relief during water charging.8 供电负责人 Power supply director 2 负责水压期间锅炉照明、上水泵、升压泵的电力保障工作。In charge of power supply for boiler illumination,1/1 charging pump and booster bump during water charging.9 检查组负责人Inspection group director 2 负责各检查阶段的设备检查、人员组织及清点工作,对检查情况进行
20、记录并报告操作组负责人。In charge of equipment inspection,personnel organization and checking operation in every stage and record all the inspection result,report to operation director.10 膨胀检查记录人Expansion inspection recorder 1 负责水压期间膨胀检查、膨胀指示记录工作。In charge of recording about expansion inspection,indication duri
21、ng hydraulic test.11 物资供应负责人Material support director 3 负责整体水压设备、材料、表计、药品采购及供应工作;负责水压药品合格证提供工作。In charge of procurement and supplying for whole hydraulic equipment,material,meter and chemicals,ensure hydraulic chemicals certification presentation.12 后勤保障负责人Logistical support director 3 负责水压期间各项后勤保障工
22、作,负责应急救护工作。In charge of various logistical service during water charging and emergency rescue.13 安全组负责人Safety group inspection director 4 负责整体水压前及过程中的安全检查及验收工作。In charge of safety inspection and acceptance before and during whole water charging.14 取样检验负责人 Sampling director 1 负责水压用水的水质取样及送检工作。In char
23、ge of hydraulic test water sampling and inspection.15 检查验收组 Quality supervision group 4 1.负责水压前压力表计校验送检及取证工作;2.负责水压药品合格证保存及报验工作3.负责水压用水的取样送检及取证工作;4.负责整体水压试验前及过程中的质量检查、验收取证及签证办理工作。1.in charge of pressure meter calibration inspection and certification acquirement;2.in charge of hydraulic chemicals cer
24、tification preservation and declaration;3.in charge of hydraulic test water sampling and certification acquirement;4,in charge of quality test,acceptance inspection and certificates applying before and during whole hydraulic test.16 操作人员 Operator 若干 Several 负责水压过程中所有阀门的操作执行工作。Be responsible for the
25、implementation hydrostatic test all the valves in the process of work.17 检查人员 Inspector 若干 Several 负责水压期间各阶段检查工作,发现问题汇报到检查组负责人。In charge of inspection work at every stage during water charging,and report the found issues to inspection group director.18 救护人员 Rescue personnel 2 负责现场紧急救护工作。In charge of
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 660 MW 火电 机组 锅炉 水压试验 措施
限制150内