高速公路工程综合设计毕业设计说明书.doc
《高速公路工程综合设计毕业设计说明书.doc》由会员分享,可在线阅读,更多相关《高速公路工程综合设计毕业设计说明书.doc(44页珍藏版)》请在得力文库 - 分享文档赚钱的网站上搜索。
1、毕 业 设 计 (论 文) 学院 专业毕业设计题目: 上饶至南昌高速公路C段工程综合设计姓 名: 班 级: 1 0土 木 ( 道 桥 ) 学 号: 指导教师: 完成日期 2 0 1 4 年 4 月 30 日 上饶至南昌高速公路C段工程综合设计Integrated design of C engineering of Shangrao to Nanchang Expressway 总计 毕业设计(论文) 43 页 表 格 8 个 插 图 8 幅 摘 要 上饶至南昌高速公路是全国公路往中的一条重要干线,对上饶地区的经济发展起着很大的作用。本路线途经平原微丘区,本着安全、经济、实用、美观的原则,对上
2、饶至南昌高速公路C段进行工程综合设计。 本次设计的主要内容包括:确定设计参数,路线方案的比选,平纵横设计,桥梁和挡土墙设计,路面结构设计,全线施工图预算等。严格按照标准的要求设计规范,结合当地的地形和环境,考虑合理的线路布置,应用计算机软件的应用图。最后完成了所有设计内容,绘制设计图纸,编制设计说明和有关参数表格。关键词:高速公路; 路线比选; 平纵横设计; 路面结构设计 Abstract Shangrao and Nanchang expressway is the road towards an important trunk, plays a very important role in
3、 the economic development of Shangrao. The route in plain and hilly area, in line with the safe, economic, practical, aesthetic principle, engineering design of Shangrao and Nanchang Expressway C section.本次设计的主要内容包括:确定设计参数,路线方案的比选,平纵横设计,桥梁和挡土墙设计,路面结构设计,全线施工图预算等。严格按照标准的要求设计规范,结合当地的地形和环境,考虑合理的线路布置,应用计
4、算机软件的应用图。最后完成了所有设计内容,绘制设计图纸,规格和设计参数表。 The design of the main content includes: determining design parameters, selection of scheme design for the horizontal and vertical lines, bridges, and retaining wall design, pavement structure design, all the construction drawing budget etc. Designed strictly ac
5、cording to the standard requirements, combined with the local terrain and the environment, consider the line layout reasonable, application of computer software applications. Finally finished all the design, drawing design drawings, specifications and design parameter table.Key words: Freeway ; Comp
6、arison and selection of route ; Design for the horizontal and vertical; Pavement structure design 目 录 摘要IIAbstractIII第一部分 设计说明书第一章 绪论11.1 概述11.2 选题意义2第二章 路线总体设计32.1 概述3 2.2 设计资料32.3 设计技术指标及技术规范32.4 路线总体设计原则7第三章 路线平面设计53.1 概述53.2 选线的一般原则53.3 选线步骤7 3.4 选线与路线方案比选8 3.5带缓和曲线的圆曲线计算9第四章 路线纵断面设计11 4.1 纵断面设计
7、一般原则11 4.2 平纵组合设计11 4.3 竖曲线设计计算14第五章 路线横断面设计16 5.1 横断面设计各项技术指标175.2 排水设计18 5.3 超高设计19 5.4土石方计算和调配23第六章 桥梁、通道及支挡物设计266.1 桥梁及通道设置266.2 挡土墙设置及稳定性验算266.3 坡面防护29第七章 路面设计307.1 路面结构设计资料307.2 路面结构设计327.2.1 设计方案317.2.2 确定土基的回弹模量337.2.3 路面结构设计33第八章 施工图预算398.1 预算定义和作用398.2 施工图预算的编制依据398.3 施工图预算项目的主要内容398.4 施工图
8、预算文件编制步骤408.5施工图预算价格41结语42参考文献43第二部分 工程图表 1、路线平面图2、路线纵断面图3、路线横断面设计图4、标准横断面设计图5、路面结构设计图6、挡土墙设计图7、路基排水设计图8、逐桩坐标表9、纵坡、竖曲表10、设计表 11、土方设计表 12、路基超高加宽表13、边沟排水沟设计表14、主要经济技术指标表15、施工图预算表 v 第一章 绪论1.1 概述 高速公路的规划和建设是中国目前实现经济和社会发展的需要。目前,我国是交通基础设施建设的关键时期,全国各地都在极力提高运输系统,以满足日益增长的交通需求。 上饶至南昌高速公路是我省高速公路网规划加密的高速公路项目,由上
9、饶市政府批准进行建设项目的前期工作,目前在可行性研究阶段。该项目是由上海至昆明国家高速公路在上饶市附近,流经上饶市,上饶县,县,德兴市,建设里程约65.6公里。上饶至南昌高速公路C段全长6.356km,设计速度为120 km/h。全线共设置2个平曲线交点,。该路段处于平原微丘区地形,地势平坦,全线高差约40 m。 2.2 选题意义 本次毕业设计的意义在于运用所学的专业知识,根据自己的未来工作服务对象,在老师的指导和帮助下独立完成施工图设计任务中的一段公路。通过本次毕业设计可以培养我们对施工图设计的能力,把学到的知识系统的运用到理论与实践中去。熟悉掌握平纵横设计、路基设计、路面设计、桥涵挡土墙设
10、计及施工图预算的具体设计方法,并能够独立完成全部设计的图表。满足以后生产实践的需要,为自己以后的工作打下一个坚实的基础。36 第二章 路线总体设计2.1概述 总体设计是在建设规模的前提下,综合考虑,整体布局的一体化设计,使各专业设计协调配套。总体设计的目的是设计一个完整的统一体,防止设计不协调,布局不合理的出现,以确保整体布局及公路工程项目设计经济合理,提高设计质量和水平。 2.2 设计资料 本段线路位于江西省上饶地区,平均海拔为210米,气候为热带雨林气候。土体成分主要为黄粘土,地表附有1030 cm腐殖质土层。地表岩石主要为中分化的沉积岩。该区域公路建设材料十分丰富,可以充分利用当地建设材
11、料,如砂,砾石,碎石,石等。此外,还有其他建筑材料供应充足,如沥青,水泥,钢材,木材,石灰煤渣等。According to the specification of highway asphalt pavement, the design life for 15 years, should satisfy a service level. According to the traffic data shows that, the design of the initial annual average daily traffic of 5000 vehicles / day and night
12、, traffic is growing at an annual rate of 5%. 根据公路沥青路面规范,对其设计寿命假定为15年,应满足服务一级水平。据提供的交通资料可知,设计初始年平均日交通量为5000辆/昼夜,交通量年增长率为5%。2.3 设计技术指标及技术规范主要技术指标见表2-1 表2-1主要技术指标表序号指 标 名 称规 范 值序号指 标 名 称规 范 值1公路等级高速公路2路基宽度(m)263设计行车速度(km/h)1204圆曲线极限最小半径(m)6505圆曲线一般最小半径(m)10006直线段最大长度(km)2.47反向平曲线间直线段最短长度(m)2408同向平曲线间直
13、线段最短长度(m)7209凸形竖曲线一般最小半径(m)1700010凸形竖曲线一般最小半径(m)600011纵坡范围(%)0.5312坡长范围(m)30090013停车视距(m)21014汽车荷载等级公路I级 设计必须进行工程地质勘察,查明水文地质和工程地质条件。当路堤填土高度大于20m,中心基坑开挖深度大于30m,应结合路桥、隧道结构作方案的比选。2.3.2技术规范 各工程方面的设计都应按照相应的规范要求来设计,特别是对自由裁量的内容规范的范围或推荐使用灵活,不能死守规范,但也不能脱离规范。在高速公路的施工图设计,相关的技术规范有:中华人民共和国行业标准的公路路线设计规范(JTG d20-2
14、006),公路路基设计规范(JTG D30-2004),公路工程技术标准(JTG b01-2003)。2.4路线总体设计原则 根据指定的路线总方向,按照设计任务、公路和道路网中的作用进行设计,需考虑到社会,经济因素和复杂的自然条件等来拟定路线总体走向。(1) a careful analysis of the distribution of terrain, geological route to and within the scope of the building and other objects; determine and scope of movable point contro
15、l center, if along with needs across the river, the length of the bridge should be estimated, if it is a bridge across the river, the location should be as control point.(1)仔细分析地形的分布、地质路线和建筑内其他对象的范围来确定和控制中心活动点的范围,如果随着过河的需要,它是一座桥横跨在河上时,位置应作为控制点;(2) according to the requirements, seriously study the t
16、errain, the paper selected line and a paper setting out work. Line, through or near most of the control point straight, crossing the intersection. Rationality analysis before and after the line, such as the line will cause a large number of buildings demolition, whether through a large area of paddy
17、 field or adverse geological area, before and after the line length is too short. If it is not reasonable, it should adjust the individual control point position after the re threading or adjust the threading scheme according to the control point of the movable range.(2)根据上述要求,认真研究地形,来进行选取线和纸上定线工作。通
18、过附近的控制点或最直的交叉路口,理性分析之前和之后的线路。如果线路会造成大量建筑物拆除和通过大面积的稻田或不良地质区,它都是不合理的。应调整个别控制点的位置重新穿线后,再根据该活动范围的控制点调整线程方案;(3) the intersection angle and distance or by the coordinates of the intersection angle and the intersection spacing is calculated with a protractor and a ruler volume, according to the actual situ
19、ation at the intersection point, analysis the controlling factors on the horizontal curve radius and gate trim curve radius and length of transition curve, recommended radius should be considered when the relevant provisions of the technical standard of Highway Engineering topographic and geological
20、 features, requirements and related technical economy.(3)通过交叉角坐标和交叉口间距用量角器和直尺来计算其交叉角度和距离,根据实际情况在交叉点控制因素对平曲线半径及圆曲线半径、缓和曲线长度分析,推荐半径时应考虑的有关规定公路工程技术标准的有关规定,地形和地质特征的要求和有关技术经济;(4) calculation of curve elements and route mileage, according to the direct corrosion points and tangent length on topographic ma
21、p set curve straight and draw the whole curve, the design starting point or the rear curve slow straight start, amount of each kilometer pile, hundred meter pile and pile.(4)曲线要素和路线里程计算,根据地形图集曲线的直缓点和缓直点绘出整个曲线,由设计起点或后方曲线的缓直点开始,量出各公里桩、百米桩和主点桩。 第三章 路线平面设计3.1 概述 选线是基于对线和技术标准的基本趋势,结合地形,地质条件,考虑到安全,环境保护,土地
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 高速公路 工程 综合 设计 毕业设计 说明书
限制150内